Hello all,I'm thinking of using the following for an autopilot:Arduino Mega connected to:9 Degrees of Freedom - Razor IMU - AHRS compatibleSerial Servo Controller -> connected to at least 3 micro servosSpektrum Reciever65 Channel SUP500F 10Hz GPS Rec
Read more…All,
I have an Ardustation and it's working fine, but it is much more fun to
have the screen of the computer showing telemetry, although I'd like to
have the feature of tracking antenna (that's only available with the
Ardustation).
So, my question is: is
Gents, I've found a solution for who's having problems with the xBee being corrupted when starting Ardupilot.
Everytime I had to pull of the blue wire to not damage my xBee, but now I found a solution.
I've added a delay command right before the serial
I have arduPilot setup with shield V2, arduIMU, and ublox gps......The arduPilot is running code version 2.6 but when I switch it in to stabilize or fly by wire mode...the plane only will correct itself if I tilt it to the left...if I tilt the plane
Read more…Help need with the Failsafe 2.6
I lost a gas UAV from what appears to be a failsafe issue.
V2.6 with IMU V2 shield
The transmitter low set point for throttle was 1070ms, #define SET_RADIO_LIMITS 0
Failsafe set point set to 1250ms using a Spectrum AR70
Read more…Which input (IN0-IN7) controls the flight mode(autonomous or manual) by changing the mux control?
thanks!
The only thing worse than a noob asking a boring question is a cheap noob doing the same...
I am buying an easy star (shocker, I know) and looking at the RTF kit, I have a bad feeling that I am paying more for servos and a remote that could be found
I have the ArduPilot, Ardushield, IMU v2 board. Do I need to connect the Em406 in the IMU or can I connected in the Ardushield? Does it matter where I connect this GPS module?
Read more…I've been looking a bit at the ardupilot firmware and as best as I can tell, no where does the code compute an actual airspeed.
The FTDI cables are out of stock in the store. I've got the rest of my hardware and need the cable very soon. Any other sources for these or is it possible to splice one together?
Would buy one if anyone has any extras for sale.
Thanks!
John Klier
I im in the mids of looking for a suitable brushed dc motor as outputs for my quadrotor.Any suggestion on which brushed motor to use?my craft will weigh approx 400grams including payload.
Reminder:guys its normal brushed type motor and not brushless.
Read more…Today when I was trying to find something I found something reallyinteresting. Especially for us who is working on AeroQuad/AeroCopter.
IRRangefinder with I2C bus well that would fit quite perfectly to ourupcoming AeroCopter. Especially now that I ha
Hi, everybody, I have a set of ArduPilot board. I solder and connect all the necessary units together correctly, and then loading the code, testing and configuration. I can receive data in the serial port. However, after I plug APC220 http://www.dfro
Read more…I have 2 xbees that are set to 115200 baud. I am just sending the word "hello" from my arduino over a xbee to a xbee plugged into my computer with the arduino serial monitor open. I send the word "hello" every second. It shows up on my computer scree
Read more…Hi all,
i have a sony optical 3x camera lens system and also have a tremendous urge to locate its power inputs and its video out pin. if anyone knows of a website or knows exactly how to tap into this lens give me a call at 203 733 1455 or reply to this post
Read more…hey
I have a small problem.
code has loaded 2.6 and made the changes for gps and shiled.
when I start up for the first time with all the servos and all sensors,GPS, pitot tubes connected.
esc beeps on startup but nothing happens, the rudder pulls like cr
Guys,is 3-axis accelerometer enough to get a decent stabilization for a quad-rotor copter??
Read more…I would like to connect the Arduimu V1 to my Ardupilot. I do not know where to connect AP pin D6 on the ArduImu V1.
Who can help?
Thanks
Christof
Read more…