XBee Pro 900 XSC RPSMA for telemetry
Hi all,Does anyone have any experience with the XBee Pro 900 XSC RPSMA for telemetry on UAV Dev Board?ThanksRyan
Read more…
2 Replies
All Discussions (33318)
Sort by
Which frequency band to use for transmitting video whilst using a 2.4ghz controller?
I've tried to do a little reading into this and im starting to get a little confused. I've just purchased my plane and hope to get it flying this weekend and im already looking at putting a wireless camera onto it.Im using a Spektrum DX6i DSM 2 trans
Read more…Remzibi OSD - downlink with xBee 900
HiI have a good video signal on the OSD with a direct cable connection. When I try to use the xBee radios to transmit the signal, I see only snow on my screen. I tried several Baudrates. Always snow.What setting do I need for a good signal??thanks fo
Read more…Finding the right computer/microcontroller for the job
So I've been slowly working on a quad based around an arduino (yeah, I know, who isnt?). But I've recently been reconsidering whether a more advanced processor might actually save me time and money as my project grows.A processor that could handle a
Read more…Tilting gyro's axis to improve yaw noise on low velocity UAVs
Looking through the code (and the various discussions on the web) I note that the 3axis Acc uses gravity to provide stabilisation of the gyros for pitch and roll axis, but the yaw is not compensated unless there is sufficient forward motion (detected
Read more…Clarification of License?
I found this blog and links to code last night, and you guys have been really busy!I'd like to reuse the IMU code in a sample application for reading MotionPlus/Numchuck boards connected via I2C to PC's VGA port (ala 25 cent I2C adapter project), and
Read more…Beginner looking for guidance
I stumbled onto this awesome site and couldn't believe what I had found. First I want to say keep up the great work here. Second I am new to RC planes (or other vehicles for that matter) and am so new I have not purchased a plane yet but might next m
Read more…Wireless telemetry and xbee
I remember reading that adrupilot mega will be including 2 way telemetry, But i was just wondering if this will be achieved via the same xbee modules as currently used on ardupilot. Reason for asking is I was planning to buy some XBee Pro 900 modules
Read more…ArduPilot Shield
Looking at the possibility of building a navigation only system as a starter for 10.Can someone direct me to a circuit diagram for the ArduPilot Shield board please.Unsure if I need the board as have no desire at this point in time to measure air spe
Read more…Pitot tube diameter?
What diameter tube is required for ArduPilot v2.x and what effect would a larger or smaller diameter have?
Read more…Xbee 900mHz Configuation
I just purchased the Xbee Pro 900mHz. I am able to change the Baud rate for the uBlox GPS. But I do not know what I need to change for the Network IDs. There is something call Modem VID. Is this it?
Read more…nmea output on bluetooth gps
Hello all,I opened the case of my bluetooth gps and it seems to have a little plug (see red circle on the picture below). Do you think it's a nmea output ?thanks.
wings level only
I'm interested in ardupilot for an aircraft that is only a wing leveler. No course guidance or anything else is needed.Would I be able to construct this using the ardupilot board, the programming cable and the FMA co-pilot.From a brief read of the ma
Read more…Accurate Altitude Sensor for Autoland - new idea?
I've noticed a lot of people are talking about autoland - and no wonder; landing can be tricky, and is generally the part of the flight where you're most likely to break something. I plan to get my UAV to autoland, because I'm not a great RC pilot, a
Read more…Super-class rock crawler automation
Well i am starting to get things together to make my rock crawler autonomous. i have a ardupilot and arduino mega on the way. i have already experimented with a basic stamp v2 in which i was implimenting a mesmic dual axis accel. and ping sensor to j
Read more…E-trainer 140 as uav
Hello,I was thinking about the e-trainer 140 (graupner) to make my uav. It's a very light aircraft (1kg rtf for 1.4m wingspan - sorry for the metric unit) with good flight quality. What do you thinking about this model ? Thanks
Read more…Autolanding with Ultrasonic Sensor?
Hi Everyone,I have a question for you. I'm designing auto landing system with ultrasonic sensor controlled elevator.It will take the control in last 3 meters for smooth touch to the ground.And another idea using this for low level flying with auto al
Read more…Chip on ArduPilot board not in right place
I bought some extra boards and thermopiles recently here on the forum and couldn't understand why the one board wouldn't work properly, then I noticed that one of the chips is not correctly lined up on its pads. Would it have come out of the factory
Read more…XBEE Adapter For Plane Side
Currently, Adafruit is out of stock on their XBEE adapters. I was wondering if this adapter from Sparkfun would work?http://www.sparkfun.com/commerce/product_info.php?products_id=9132I am new to this so all the help I can get will be great.-THANK YOU
Read more…