Dear Community,
on a Quadrocopter i use a 3DR-Pixhawk on ArduCopter Firmware Version V3.4.2.
The FC was formerly used in another setup and had a crash last year. It seems to work fine, though.
There's just one issue i do not have enough experience with
Read more…I did not fly my ArduCopter for around 10 weeks or even more than that.Now suddenly it is showing bad compass health in the mission planner, my HUD reacts and moves perfectly according to the drone but same message keeps on showing "Bad Compass Healt
Read more…I have a gimbal which had a blown BGC so I decided to upgrade to STORM32. My first step was to connect to the PC using USB. Nothing.
I looked at the wicki and it suggested that the USB was for show and FTDI was needed. I used the Arduino FTDI hack to
Read more…Good morning!
As a school project we are building an autonomous drone that can perform certain tasks. We decided to use the Navio2 board as our flight controller and since for this project we are only going to be dealing with distances up to a max of
Read more…hello,everyone ,how to operate the ground station(missionplanner)? please give me some advice , thank you.
Read more…I use PIXHAWK burned with APM3.3.3 firmware to test the official PX4 flow sensor, (supported by http://ardupilot.org/copter/docs/common-px4flow-overview.html). Now,I can see the optflowdata in the MP(version1.3.38) status section ,then I change the E
Read more…I am just trying to run the attacker code of the link mentioned. But i am facing the following errors :
MAV> Waiting for heartbeat from tcp:127.0.0.1:5760
Exception in thread main_loop:
Traceback (most recent call last):
File "/usr/lib/python2.7/thread
I was flying my QC with 3S 4000MAh battery but for hovering 700 PWM (70%) of throttle was required. Therefore I moved to 4S 4000MAh and now the hovering PWM is 540 (54%) only but the Mission Planner shows Power Level error (as red) on the PreFlight c
Read more…I'm trying to run ArduPlane in SITL on a native debian based Linux system (Ubuntu 16.04)
In ArduCopter everything is working fine.
I followed the very good tutorial in http://ardupilot.org/dev/docs/setting-up-sitl-on-linux.html
However the intended when
As the title say "Stabilize mode like Loiter mode ！！！"
I flight my quad copter last night, i have two question.
1) Why stabilize mode like the loiter mode very stable ??
About stablilize mode , it is using GPS and Barometer ??
2) If i flight my quad copt
Read more…Dear friends, I hope this topic fits in this forum. I own a HP Touschsmart Envy 15 j000 laptop (Windows 10). I used to set a communication between MP and my laptop without problems. I formated my HD drive and tried to install all software and drive
Read more…I need to monitor the my GCS simulation from another laptop through tcp or udp. Is it possible? Can i also have control over it to modify the settings. So that i can change settings in MAVProxy .
Read more…First let's not get crazy but I was so excite to get this installed and be done with my ground station setup.I bought this apm switched and can't get it to work with my flysky re-i6s I tried on one of the switches but it only sent the signal for 1000
Read more…I'm looking for an open design that I can mill myself. I have a set of 8 U8 motors to be run with 26" props and I want to design a craft around that. I was thinking of taking a Tarot X4 and replace the stock arms with the arms from a Taror X8. The co
Read more…I kept on upgrading 3.2.1 but then came to know that for APM 2.5 the upper versions are not compatible. I am stuck now because I cannot find the 3.2.1 installer at all. I have the already downloaded zipped file but when I extract it I get some folder
Read more…Large drone (700mm Hex) pitched positively just about at the ground (12inchs ish...) during an autonomous landing. I think, I can see in the logs where it tried to correct but did not physically do so.. I believe I can see also where I tried to give
Read more…Hi all,
I newly developed a fixed wing drone with Bixler 1.1 from hk.
Below picture is autopilot cockpit module I designed for pixhawk.
I had to extend front section of the cockpit from its original length to fit longer pixhawk into the cockpit.
Also not
Read more…Thanks in advance.
I have a 450 clone helicopter with a Tarot FBL head and APM 2.6, flying fairly well for just starting out, usually I am flying quads..
Question 1 can I use mission planner flight mode ALT HOLD with this FBL helicopter setup with jus
when playing back my movies they are very choppy and sometimes stop.i have a solo3dr, solo gimbel, and a gopro hero 4 camera. tried different settings on the camera but still the same
Read more…