Hi,
Is there something I've missed to pass through the throttle single from the receiver to the ESC?
The ESC beeps continuously when armed.
I'm using QGC 3.0.2 with the Flying Wing/Skywalker X5 Firmware 1.5.1dev. The ESC calibration seems to work tho
Read more…Hey guys. Although I have flown many quad copters and have built many rc planes, when it comes to building a quad copter, I am clueless.
One of my biggest questions is, I own 2 smaller quad copiers, they are both rtf, toy grade, simple cameras, and th
Read more…Are there certain restriction or guidelines to understanding the dead cat arm ratios and angle ratios
Read more…Hello, i had a big crash and i need help figuring out what happened
My setup:
During the
Read more…Hello,
I got Hobbywings platinum 30A ESC-s.
When they are connected to the Rediolink R9D reciever, they work fine.
If I connect them to APM 2.8 - they does not like the input (throttle) pulses.
I measured the R9D pulse period - 14 ms (71 Hz).
By moving t
Read more…I started the project of creating a new kind of air combat for model aircraft (airplanes and helicopters), and drones. This is for models with remote control, contactless battle. Will lead scoring lesions using a laptop or a smartphone. Who thinks ab
Read more…Hi,
I've got the FlySky i6 with the 6 channel receiver. Not received the 10 channel receiver yet but would like to change the pixhawk flight modes with what I've got so far.
I can see in the APM Radio Calibration that channels 5 (1000,2000) and channe
Read more…I've searched and can't come up with a direct answer, and the wording leaves it vague in my mind.
1) Is MOT_CURR_MAX for each motor, or the combination and total current? In reading it sounds like it is intended to save the battery from excess current
Read more…Hi, I am trying to use a pixhawk on a large (2000mm frame) custom variable pitch quad copter but am having a hard time getting the ball rolling. I have read that you can save the mixer file on the SD card for easy editing but I cant find the mixer fi
Read more…Im wonder if there is some option in Mission Planner that allows me to set max fly alltitude. Let say that I don't want to allow my drone to fly above some certain altitude value even if throttle is set to high.
Read more…I am using a Pixhawk Mini with QGroundControl on a YoCoo DIY F450 Frame Kit.
After I set everything up and calibrated the ESCs in QGroundControl, I found that not all of the motors were spinning at the same speed (even at high throttle levels above 5
Read more…Hi,
I have a Pixhawk with M8N GPS module but it's not detected. I've tried the latest firmware on both QGroundControl and APM Planner but neither detect the GPS module. The GPS port is providing ~5v so the module is getting power and all the connect
Read more…Hi Greg
I want to ask you if I can switch between the arducopter and arduplane during the flying using only pixhawk controller without the bridge and two different controllers?
I've already seen that we can do the transition in pixhawk, we can use tha
Read more…
Having just got back from emergency, I thought i would mention how important it is to remove the props when doing any esc calibrations, testing or what have you when in closed quarters. I've been working with drones for about 3 years and until now
Read more…Hi,
I attached log file URL (18mb), if someone could review and let me know if anything is off or wrong.
Towards ending of flight, I had no throttle. it went to 0% and no matter what range I gave it. Nothing.
It's possible I had no RC controls and not j
Read more…Hello All, i'm working in a bigger Tarot hexa, the TL6X001, i have the Tarot 340 kv motors and
Hobbywing 40A ESC 2-6S no BEC. (pls see attached img)
After flying 20 minutes (without payload) escs are really hot , yesterday i burned one in flight and l
Read more…Hi,
I want to share a review/comment we got recently. Our Kickstarter Project had quite some help through this community!
Here’s a link to my YouTube review of the Bat-Safe!
Awesome product!!! https://youtu.be/ASiLqVecXfQ
That's the o-tone, not altered.
Read more…Hello,
I recently built a 250 class quad that is ideal for FPV flying, and after flying it around for a little while line of sight I'd like to get into flying FPV. I'm looking at buying the Quanum DIY v2 Pro goggles, since they are cheap and apparent
Read more…HELP
I bought a XUAV Talon with wing extensions in 2015 and still haven't been able to fly it using waypoints and using the RTL. I am able to fly it manually.
The radio is set up with Manual, FBWA and RTL
Pixhawk with the latest Plane3.7 and Mission Pla
Read more…Hello, Iv just built my pixhawk quadcopter but I have problems with the neo 6m gps. I get 6 sats 3d fix for about 5 seconds, then 0 sats for about 5 seconds and this repeats forever. Are there any params I can tweak or its a fault gps unit? I have so
Read more…