Hello,
I am at the moment just trying to learn mavlink specifically on my 3dr Solo. I am trying to communicate with the Solo on my laptop, my laptop is acting as the controller "WiFi AP". I have a custom program which sends commands to it or at leas
Read more…Hi every body
I have a question about the limits which are applied on the speed in advanced parameters
I am actually looking for a way to increase the max speed, my copter can fly in loiter mode
in advanced parameters there is a parameter named WPNAV_LO
Read more…hello every body
I have a question that can we choose a speed limit for WPNAV_LOIT_SPEED more that 20 meter per second or not?
actually when we change it in full parameters it changes (after giving a warning) but I dont know that will it take effects o
Read more…I posted this in the copter 3.3.x forum, perhaps it was the wrong place? Reposting in the hope of getting some insight, google has let me down and I can't seem to find anyone else with this issue (suggests a possible fault with my pixhawk?)
Anyone?
Che
Read more…Hi All, (pixhawk 3.2.1 Quad X refers)
During a Batt FS Auto Land recently, the quad tipped over on landing.
I suspect that it tipped-over since the terrain was uneven.
I saw this youtube vid where it appears that the quad 'detects'
a possible unev
Read more…Hi!
I will share to you the repair and enhacement procedure i did to my Turnigy 9X8Cv2 receiver.
The Rx comes with a minimal antenna, possibly 2dBi, monopole type.
It's made of a full wavelenght mini coax cable, a sleeve balun to avoid detune from coax,
Read more…Hi All,
I have flown my quad 12 times now, using the stock pid param as per 3.2.1
I get ~25min per flight with small HD Tube nose-mounted FPV cam.
I now want to attempt Auto-tune to optimize the rig.
I don't think I am experienced enough to do PID tunin
Read more…Hello every body
I want to tell you the story of one flight test with pixhawk
recently I installed the pixhawk on tarrot x650 and attempted to flight
when we started to fly the quadcopter took off the land correctly but a little agile and sharp. when th
Read more…Two CW on top two CCW on bottom. RCOUT for CW is 1600, RCOUT for CCW is 1400. The copter is balanced good and fly's like a dream compared to my dji f550. Any one having any thoughts on the difference in output would be greatly appreciated.
youtube of
Read more…Hi All,
Today's flight felt very unusual. No crashes, but I frequently felt my quad was behaving strangely.
I checked the log file and note that over my 20 minute flight, it threw the error EKF_CHECK-2 (subsystem 16, error code 2, bad variance) 20 ti
Read more…Until the last update MP had always been working perfectly. When I click OK to update it updated the files but crashed after that.
It was really frustrating as I was getting ready to go fly. It took me more than an hour to get V1.3.36 loaded from back
Read more…Good afternoon
Available modem model: XBee PROS3B XBP9B-DMST.
I am trying to sew on XBP09-DP nothing comes(
Help me please.
Read more…Hi there, I just did a new build with a new pixhawk and i am sometimes getting the compass variance error.
Did the compass dance several times but to no avail. Strange thing is the fact that sometimes it is just alright and just lifts off without the
I just moved my Pix from a y6 on 2.x and I believe <3.3 to a y3 on the latest 3.3 release.
Yaw on the y6 was snappy, and control input was stellar- my throttle response felt instantaneous.
Input is SBUS on RC port on a FrSky x8r from an X9D Plus TX.
Mov
Read more…I wonder what the general consensus is for what people now use and prefer for the throttle stick and whether to have it spring loaded so that it sits in the middle (hover position) compared to having it un-sprung as we always used in the past.
I can
Read more…Hey guys,
I have a 3DR Iris+, and I replaced the AA transmitter battery pack with a Turnigy 2.65 mAh LiPo battery as instructed here:
https://www.cloud-surfer.net/2014/07/14/lipo-for-3dr-iris-rc-transmitter/
I fully charged this battery once, with no is
Read more…Hey guys,
I have a 3DR Iris+, and I replaced the AA transmitter battery pack with a Turnigy 2.65 mAh LiPo battery as instructed here:
https://www.cloud-surfer.net/2014/07/14/lipo-for-3dr-iris-rc-transmitter/
I fully charged this battery once, with no is
Read more…For a strange reason to me after completion of ESC calibration my motors use to spin all together but not with the same power in order to fly my quadcopter.
After various efforts to fly and adjust one of my motor does not spit.
1. - I Plug Power Modul
Read more…This amazing product hopefully can be integrated for Pixhawk.
https://www.kickstarter.com/projects/scanse/sweep-scanning-lidar
Read more…I have an Iris+ (https://store.3dr.com/products/IRIS) connected to a raspberry pi companion board. My goal is to fly the drone autonomously, without a remote controller. Here are my drone specs:
>>> ArduCopter V3.2 (c8e0f3e1)
>>> PX4: dea2cfd1 NuttX: 7
Read more…