HI all
I am using 3.2 firmware on my quadcopter F450 with 2.8apm FC
I am making 6 waypoint with auto take off, using Do jump command with -1
Means unlimited loop,
All flight is ok but went it hit minute 2-8 each waypoint the quad will going down abit eac
Hi,
I've done lots of thread-searching but haven't found a fix; any help would be appreciated.
I am in the process of upgrading from APM 2.5 to APM 2.8. My problem is that I cannot get the GPS / Compass to work. It is (they are) a Ublox Neo module(s).
T
Read more…i am working with APM 2.8 and when I conected to MissionPlaner this screen is shows:
why shows fly mode 5, 4 and 1?
also on the flight modes settings I can not change, only this screen appears and transmitter does not generate any change.
Hi,
i had a 200mw Boscam transmitter, with a RC805 receiver.
i only had about 300m range, so i bought new antennas and a 400mw boscam transmitter.
now i have about 350 to max 400m range and the channels are somehow not as shown in the manual.
why does th
Read more…With URUS you could make like automated control Home, Robotics Games (Like Lego Mindstorm) and more, working with APM Apis and Raspberry Pi under Linux OS.
At first time i will try get this work for Domotic System (Automated System Home), you could do
Just setting up my first plane with Pixhawk Lite/plane 3.5 and I am witnessing some rather strange failsafe behaviour whilst the plane is on the bench and disarmed, with no available GPS signal.
I am using FrSky Taranis X9D+, so have radio failsafe co
Read more…Hi,
I'd like to built a foldable quadrocopter which I can take with me on a round-the-world trip. When folded it should be small enough to be carried in a backpack, so I can take it with me on (shorter) trekking tours.
What I ultimately want is a quadr
Read more…Brand new sealed unused:
1. Xbee Pro 868 RPSMA - 20 USD
2. Xbee Pro 868 Wire Antenna - 20 USD
3. Xbee Pro 2.4 RPSMA - 20 USD
4. Xbee Pro 2.4 Wire Antenna 20 USD
Everything for 70 USD
Else refer to individual prices.
Paypal plus fees.
Shipping worldwide
How does the Tower "land" function work - in regard to altitude? I have a mission that is set to 50 ft altitude for the whole thing. When I add LAND, it shows a down arrow and "75.0 ft". I do not understand why it would land 75 ft from a 50 ft altitu
Read more…Good morning,
I own a 3dr x8 UAV which was recently discontinued. 3DR left its costumers hanging with no spare parts or support. I need to replace some bad esc and motors. Can I change just the damaged ones with some aftermarket ones or do I need to c
Read more…Hello there. First of alI, I apologize for my poor written English skills. Over the past couple of days I 've been trying to get my mind around this interesting project I accidentally came across while researching gas/electric powered multirotor plat
Read more…I have the APM 2.6 board. I want to power an external device (an MCU) using the telemetry port pins (which is basically a UART interface). The Vcc pin of this is rated at 5V, as i see with my multimeter. The MCU i want to connect is rated at 3.3V so
Read more…After having tuned my loiter mode's horizontal parameters via LOIT_MINA / LOIT_MAXA / LOIT_JERK to my liking I am finding Loiter mode quite nice now.
Its actually my mode of choice now. Bumping those two up along with the max speed has made a huge dif
Read more…Would like to setup a second pixhawk that would crash the plane (full down elevator) if for whatever reason the plane has deviated more than 100 m buffer from the geofence set on the main pixhawk.
This is for additional safety and would also ensure t
Read more…Hello,
My first post related to my long-haul home-grown project of a quadcopter : a 1kg, 50cm span UAV.
I intend to put as much knowledge as I, fellows from France, and hopefully you will be able to bring!
First is about flight envelope. Specs aimed at
Read more…Hello guys, when I tried to compile the arduino mavlink on my arduino uno, I found this error" # error Must include FastSerial.h before the Arduino serial driver is defined".But I have already include Fastserial in my library, why does that happen? B
Read more…I have a Iris+ with the FS-Th9x Controller.
The controller displays the Altitude and Battery Voltage of the Model. Is there any way to make the controller give a low Batter Level Alarm for the Model?
Read more…This is mostly about the sensor presented here:
http://plane.ardupilot.com/wiki/common-rangefinder-maxbotix-analog/From what I gathered, this sensor helps multi-rotors maintain precise altitude control but is there any use for this in Plane like landi
Read more…This is how you modify Ardurino code for custom irregular shaped ships. There is no need to modify code for a ship with a frame that is laid out like a:
- coaxial triangle
- square or rectangle
- regular hexagon
- regular octagon
Sometimes even if the sha
Read more…