have to do level after every flight, why? FBWA mode
After every flight i have to level the plane, unless it pitch down on FBWA
Why is that? why its reset after each flight?
Read more…
0 Replies
All Discussions (17288)
Sort by
How to make a cable to connect PX4 to Intel Edison on Arduino board?
Hi everyone!
I'm going to use an Intel Edison companion cpu to control the PX4 and give orders to it. I already installed everything I need on the Edison according to this guide.
Now I only need to connect it physically. so I found this - https://pixha
Read more…reverse channel outputs on quadcopter configurations
Hi guys
Somebody can tell me how to reverse the pwm outputs on a quad copter configuration ?
I am using a quadcopter firmware on a variable pitch quad, the problem is that i need to reverse the directions of the servos number 3 and 4 ( the ones that in
Read more…Iris Parts For Sale
I have a box of Iris arms and legs, probably 4 sets, plus a bunch of new props. I also have the internals from swapping to the Iris+.
Make me an offer, prefer US sales for ease of shipping. I would consider shipping international at buyers expense, ju
Read more…Drone topographical survey for agriculture in Africa - What have we done wrong? Business opportunity
Dear all
We are developing a large-scale agriculture project in Nigeria (5,000ha) and started to use drones to survey and map topography.
The intention was then to use the Digital Elevation Model for irrigation planning and design. However, when we pos
Read more…CG settings, or best practices
I've got a small 250 sized copter, and can't get the CG centered. It's about 10mm to the rear.
It flies fine, and if I take off quickly, everything works properly. If I try to take off slowly, it flips over to the heavy side.
Are there any arduc
APM Quadcoper X4 with inverterd or down facing motors
Hey Guys,
In need of some help. Im trying to mount the motors facing downwards in my quadcopter with apm. what is the procedure to do so ? Can i simply Face the motors down invert the propellers and fly ?
Please help me out in solving this issue. Is A
Read more…Purpose based calculator for multicopter or fixed wings
As till now a feasible build approach for a platform is always based on the purpose and payload for a starting point ecalc is a great help when deciding which combo should make a good fit.
Is there a calculator available with similar characteristics b
Read more…WPNAV parameters changed to 0 after autotune??
I just did an autotune and was scanning the full list of parameters after and noticed that some of the WPNAV parameters got changed to 0. I'm not sure if they were like this before but it doesn't seem they should be 0.
Also it's impossible to scroll d
Read more…Quad collective pitch
Hi every body.
Happy new year to all of you.
I am writing to France, sorry for my very bad English ...
From some month, i am working on a full collective pitch quad.
From now, i'am using a naze32 acro controller on it, but i would like to go ahead with t
Read more…Pixhawk with 3Dr radio and minim OSD
HI
I have a pixhawk (currently on 3.2.1) with a 3DR radio on telem1 and a minimOSD on telem2. I am looking for recommendations as to what the parameter settings SR0,SR1,SR2 etc would be best/recommended for this setup.
Thanks
Andy.
Read more…Problem with OPTO ESC and APM 2.6
Hello,
i have issues calibrating/using OPTO ESCs with APM 2.6. No matter what i do i cant calibrate or make them work, using either all at once or one by one method. There are only black and white wire on the ESC. Im using APM power module. There is a
WOD mavlink ground station ;-)
Hi all.
im working on new gs software. I`m working on it becouse its connected with project WOD,
but this part is not ready for public,so i will present it later :D
but please you can help me , if you will write me here or to email p.cz@seznam.cz FEATU
Read more…3m Wingspan Mugin UAV for sale...
http://m.ebay.com.au/itm/3m-Mugin-UAV-UAS-Airframe-and-engine-kit-/301839062376?nav=SELLING_ACTIVEMy mugin for sale...No time to complete.Engine, prop and airframe. No electronics.
Read more…Live Calibration and Compass Motor Calibration
I made some changes recently and thought I would redo the Live Calibration and Compass Motor Calibration. I ended up doing it a few times and was wondering why I would get different results. I'm doing it wirelessly and am holding it in the air for th
Read more…COMPASS_EXTERNAL is set wrong?
I was just scanning through my Full Parameter List and noticed this parameter set to 0 but the instructions seem to say it should be set to 1. I have the external 3dr GPS/Mag connected to APM2.6. 2 cables going to it. I haven't haven't noticed any pr
Read more…Tuning for filming
I just finished installing a brushless gimbal on my cinetank and wanted to tweak the tuning. It's flying and filming very stable but I think it can be better. My normally tuning procedure is to wait for a calm day and use autotune. That is fine for n
Read more…Upgrade to 3.3.2 - Alt Hold rising full trottle up
Hi All!
My Pixhawk is installed on Mariner quad (500). With the version 3.2 it has many nice flights, with very good ALT Hold control and AUTO flights.
After recent upgrade to 3.3.2, it changed its behavior: in Stabilize all is OK, stable and smooth co
Y- frame pixhawk reversal
Evening every one. Is it possible to mount and or program the pixhawk on a Y Frame where the tail of the pixhawk becomes the nose
Read more…AHRS orientation:24 = compass inconsistencies
HI all,
Stuck on this one. Got a pixfalcon at Orientation 24 in AHRS (Pitch up by 90') in a waterproof drone, with the GPS/compass at the normal horizontal orientation.
The problem is EKF is permanently red and pre-arm fails with compass inconsistencie
Read more…