I want to add a payload drop feature in my rc plane for which i need to know the bearing of the plane. I am using PIXHAWK autopilot. Can anybody tell me the variable already used in firmware which provides the bearing of the plane?
Read more…Hi all,
I was just wondering if anyone knew when (or if) 3drobotics will have the pixhawk II for sale. I'm looking at buying a ap for my new quad, but if the II is on its way, I might wait a bit longer.
Thanks,
Ryan
Read more…Hi.
I need your help please, I want make a test of mi pixhawk in the terminal of mission planner but i can't. when I click above connect should open the com like this.but only gets this
can anyone help me please? what am i doing wrong?
In the first instance I was having erratic flying with my Quanum Nova (CX-20) and I determined to redo the Mission Planner procedure (16 steps)
I had done this earlier successfully but last week I had a crackup and I was required to replace the top an
Read more…Hi,
Could somebody please advise what would be the best developer's platform for high end R&D purposes, such as autonomous flying, running ROS packages, multi vehicle testing? I am currently considering either 3DR Solo or DJI Matrice 100. Money is no
Read more…After updating from 1.3.32 (worked well) to the new version 1.3.34, Mission Planner was no more able to connect to the internet... satellite data, firmware updates and software updates... etc.
It was quite easy to find out that the Firewall of the Nor
Read more…Not sure where to post this as I have seen "antenna tracker" in a few different places.
I would like to reuse a piece of equipment that has steppers to move the pan and tilt axis. I have had no luck in finding antenna tracker electronics that would d
Read more…We have a Blade 350 qx2 and we had the body off of it. Now when we try and power it up we get a yellow blinking light with a flat sounding tone. The red and blue light blink on the main board and then the blue light goes out and the red light stays o
Read more…Dear all,
I am flying a fixed wing aircraft with the FPV/OSD kit from 3DR. I have it plugged into the telemetry port 2 on a Pixhawk and I am seeing telemetry data displayed on my screen (3DR Black Pearl HD screen). However, I notice that the horizon i
Read more…Hello,
as I plan to extend my flight time and distance range, I decided to proceed with the build of a Li-Ion battery pack. I know that generally the disadvantage of Li-Ion 18650 batteries is the low discharge rate that they offer, so I need to be car
Read more…Is there anyway could see internals of a drone spaying fertilizer , i need to figure out how to balance the aircraft with fuel fertilizer and components insde,
Read more…quad spec:
f450 frame
Lipo 2200 battery
APM2.8 board
SimonK ESC 30A
Sunnysky Angel Series A2212-13 980kv
1045 propeller
im having a great fly before just until im trying to remove waving video. i mount rubber foam on my motor, and now it start to act strang
Read more…Also tried to bind to a dx18 but only see 7 channels working. I tried using the instructions at the bottom of pagehttps://pixhawk.org/peripherals/radi...l/spektrum_dsm, still no luck
Read more…Hi, first of all so sorry for my bad english, I have questions.
1- I sold naza I have bought pixhawk on 3dr store and load firmware 3.3.2 hexa on mission planner v1.3.34. But I haven't seen green status line while loading firmware, I have seen bule st
Read more…Guys I have the latest firmware on and having throttle issues. It's lagging by a second. Give it throttle and it takes a second for the blades to start, same thing when i kill it, the spin a second after.
Read more…Hello,
I have been off and on over the past couple weeks trying to get a reliable connection from a GCS installed on my MAC to connect to SITL running on a VM in VirtualBox using Vagrant. One of the tutorials I have been fallowing is here: Setting up
Read more…I am using a Iris+ with the Iris+ FrSky controller. When I turn the knob to the right that controls the gimbal it moves up and when I turn it to the left it moves down. This seems backwards to me. Is there a way to reverse this?
Read more…Has the bug with swapping channels 1-4 using RCmap and the channel attributes not getting swapped been fixed in 3.3.2 or do you still need to use the workaround and manually swap the channel attributes for the affected channels.
Read more…Well, weird issue here with Mission Planner 1.3.34 and Flight Gear 3.0.0
I followed the instruction on wiki. But can't find the start FG button !!
All I have is Start SIL and Start Xplane.
Where am I wrong ??
Has anyone heard of using the DJI Datalink 900mhz radio to link up to a 3DR (or RFD 900) radio on the vehicle?
I cannot figure out the settings for the DJI (net id, etc) and am not able to connect to it on the COM port through mission planners config
Read more…