HI,
I am searching for a solution where we select a moving target and the Gimbal will follow it regardless the copter/plane movement.
Till now, we need 2 operators, one for the copter and the other one for the gimbal to follow the moving target, but i
Read more…hello everyone ( copter pilot ) ^_^
i have convert my f450 frame into tricopter, and i having great fly with it
i have questions here:
1) just wondering, is it matter for yaw motor level to be same as the other? because once it try to lift on the air,
Read more…hi,
trying to setup a new copter with Pixhawk FC and mission planner I realized that the option *DISARM_DELAY* is not available ??????
The 3 or 4 seconds idling after arming and after landing are way to short...... in my opinion.
Will it come back later
Read more…Hi! My first post! Not sure what categori my question fits in..
What I want to do is flying a small radio receiver to predefined waypoints, and do RF-field strength measurements from a transmitter on the ground. I want the UAV to hover at the waypoint
Read more…Hello.
I've kinda decided on getting the Yuneec q500 because it comes with the case and also the handheld device (which I'll need for inside the houses and much more)
But I still think the P3 has slightly better camera quality. Can't quite tell what,
Read more…Hello, guys.
I'm trying to make Quadcopter X Tailsitter - VTOL.
It is just like X pluseone (http://xcraft.io/x-plusone-drone/) right?
So I'm looking for information for it.
However, I couldn't find anything about this.
Even at the pixhawk webpage(pixhawk.
Read more…Hi
I am trying to get GPS Lat/Lon, heading, speed and altitude info form UD5 to add RTH and Altitude Hold to my Open pilot based quad, share your ideas and let discuss what is the best way to interface it. I have few ideas how to do this
1) Get GPS inf
Read more…Hi all,
Been wondering if it I have a problem, or there's a bug in the ESC calibration mode.
Been running a pixfalcon for a while since 3.3.0 and recently came to do a rebuild / update to tidy some wiring and software updates to arducopter, OSD and cro
Read more…I have this unit and am getting less than 5 minute flight time until warning comes on. 85% Battery remaining after flight.
Total Weight: 2750g
Batt: Multistar 10000mah 4S 14.7V 10C
• Tarot 650 Sport frame with hood and electric retracts
• Pixhawk S
I am using Pixhawk on a fix wing airplane and very often I don't empty the battery in a single flight. The problem is if I restart the plane, the battery percent meter will start from 100% again.
Since I use normal batteries and no smart batteries lik
Read more…Dear all,
I am working on Quadcopter with Px4 board and trying to mount 2 I2C Sonar sensors on my Drone for obstacle avoidance
I follow this article to use 01 Maxbotix Sonar sensor:
http://copter.ardupilot.com/wiki/common-rangefinder-maxbotixi2c/
Is th
Read more…Hi guys, I have not followed the last release, so I got very upset when I updated my old, steady 3.2.1 Octa-Quad multirotor with the new 3.3.2. Of course I do realize that my system is kind of a mess, because I am using that multirotor for research a
Read more…I have a LI-24 Lipo/LiFe Charger
http://www.rcplanet.com/DuraTrax_Li_24_2S_4S_LiPo_LiFe_AC_Balancing_Charge_p/dtxp4620.htm
and 3 Zippy 1000 20C Series 2 Cell 7.4 volts batteries which were bought to use on FPV goggles
http://www.hobbyking.com/hobbyking/
Read more…Hello,
I am currently having a problem with an RFD900 Radio. The connection is not always good at startup and the loading of parameters is slow.
Is there a way to disable the "loading params" process on mission planner? Is there a problem with just can
Read more…I have used mission Planner on my sony and Apm planner on Mac. The main difference is I cannot get to the full parameter list on the Mac. I am probably missing it. I would prefer to use the Mac, is there a full list somewhere so I can check SR settin
Read more…Hello all!
I am making a quadrocopter (APM2.6) with self control with ability to fly witout remote control.
I am using a Raspberry Pi and mavproxy to make it.
It works good except one thing. To start the fly, I have to short press accelleration on the
r
Read more…Hello fellow DIYers,
I have been using the 3DR x8 coupled with a GoPro 4 Black and Pix4D to do topographic surveys for over a year now. While I have had great success with this platform, I have been having one issue that I just can't seem to find a
Read more…How are Deagonfly getting publicity in the commercial UAS world for this?????? [url]http://copter.ardupilot.com/wiki/common-ads-b-reciever/[/url] It does annoy me when a community of developers work hard to develop something and some company uses it
Read more…Hi Guys
I have a project, as indicated above, to track a high altitude object.
It appears to be feasible to use a gimbal inverted and set the ROI altitude to a large value. I have not yet discovered what the variable range allows. Mission planner lets
Read more…Dear Sirs,
i down load the source code QGroundControl2.8.0 and want to build in Qtcreator5.5 platform, but the result show me as following:
Project ERROR: MAVLink folder does not exist at 'libs/mavlink/include/mavlink/v1.0'! Run 'git submodule init &&
Read more…