I am trying to sync a waypoint (longitude & latitude) into flight plan through the database that is on my server that I am hosting, the database has both my current latitude and longitude which are generated by my android phone and then posted to the
Read more…I want to be able to trigger a quasi fail safe condition based on a condition outboard of the Pixhawk but still on the craft. How can I "send a signal" into the Pixhawk in order to enable RTL? My onboard Rx is an X8R. Thanks!
Read more…if i using an HMC5883 as 1st external compass.can i connect another and make it be 2nd external compass?
Read more…Aeronavics (www.aeronavics.com) is a manufacturer of industrial multi-rotors, based in the Waikato region of New Zealand.
We're currently looking for a software engineer to create software for the embedded computers on our new range of products: C/C++
Read more…Is 3DR frame hardware still considered open source?
Cheers,
Antoan
Read more…Hello guys.
I live in Brazil and I am thinking of develop business services with multicopters and fixed wings.
I don't know all possible applications and I would like to ask your help with examples and suggestions.
I would suggest equipment manufacturer
Read more…I have been using the 915mhz telemetry v2 units with my Pixhawk for a while now. One of them is not giving the range that it used to and I need a replacement.
I varified the range with the use of my Fighting Walrus iDrone Link and one unit is getting
Read more…I have two APM, APM0 and APM1 boards and two Power modules. Everything was going fine, I didn't fly my drone yet. Because before i fly it i noticed that whenever I connect the battery all motor spin, I am using a joystick, didn't calibrate it correct
Read more…I'm not so familar with Pixhawk but had one already successfully setup some months ago. Now I tried to use it again for another project, downloaded latest QGroundControl (2.8.0) and updated to latest stable PX4 firmware. For me it looked like flashin
Read more…I opened the Webpage where it tells you how to operate APM with a joystick and followed it. I could setup controls. And can Calibrate. But when I go to the home screen it keeps repeating "PreArm: RC not calibrated."
Tried to change settings to low Lat
Read more…Is there a mathematical solution for preventing fly-aways?
My understanding is that the following is what causes them:
- Accel z goes negative due to ship vibration versus an actual drop in altitude
- The ship corrects by adding power
- The added power c
Hello, I can´t find the reason of my quad crash.
The ESC´s are working, motors too.
I think that was a esc sync failure.
HI,
I am searching for a solution where we select a moving target and the Gimbal will follow it regardless the copter/plane movement.
Till now, we need 2 operators, one for the copter and the other one for the gimbal to follow the moving target, but i
Read more…hello everyone ( copter pilot ) ^_^
i have convert my f450 frame into tricopter, and i having great fly with it
i have questions here:
1) just wondering, is it matter for yaw motor level to be same as the other? because once it try to lift on the air,
Read more…hi,
trying to setup a new copter with Pixhawk FC and mission planner I realized that the option *DISARM_DELAY* is not available ??????
The 3 or 4 seconds idling after arming and after landing are way to short...... in my opinion.
Will it come back later
Read more…Hi! My first post! Not sure what categori my question fits in..
What I want to do is flying a small radio receiver to predefined waypoints, and do RF-field strength measurements from a transmitter on the ground. I want the UAV to hover at the waypoint
Read more…Hello.
I've kinda decided on getting the Yuneec q500 because it comes with the case and also the handheld device (which I'll need for inside the houses and much more)
But I still think the P3 has slightly better camera quality. Can't quite tell what,
Read more…Hello, guys.
I'm trying to make Quadcopter X Tailsitter - VTOL.
It is just like X pluseone (http://xcraft.io/x-plusone-drone/) right?
So I'm looking for information for it.
However, I couldn't find anything about this.
Even at the pixhawk webpage(pixhawk.
Read more…Hi
I am trying to get GPS Lat/Lon, heading, speed and altitude info form UD5 to add RTH and Altitude Hold to my Open pilot based quad, share your ideas and let discuss what is the best way to interface it. I have few ideas how to do this
1) Get GPS inf
Read more…Hi all,
Been wondering if it I have a problem, or there's a bug in the ESC calibration mode.
Been running a pixfalcon for a while since 3.3.0 and recently came to do a rebuild / update to tidy some wiring and software updates to arducopter, OSD and cro
Read more…