I cannot get into CLI no matter what I try. i try the three returns after it connects and nothing. i see one initiate message and then it goes to gibberish? i have tried it on two computers which both used to work and now neither of them do. Help
Read more…I'm looking for a ground control station radar tracking and finding that it's harder to buy one than I thought! Here, in 2015, I thought they would be everywhere by now.
Ok, so this may be a more advanced topic than normally found on this forum. But I am struggling to classify the point clouds generated with the UAV. After Pix4D, after Agisoft or others you are left with an unclassified point cloud If I want to class
Read more…Hello,
I bought this copter from a fellow last year, but have only had a chance to fly it less than a dozen times. I am completely new to this, so it has been a steep learning curve. I am worried that autopilot has had issues since I got it, but I w
Read more…Hi everyone how has same knowledge about thermal cameras
I am geo-scientist and is interested in doing Thermal Mapping with my Skywalker 1880 platform, in order to create thermal orthophotos maps of specific areas of interest. I am planning to make us
Read more…hi, i have a quadcopter with APM2.6 , and i have a problem when downloading my logs from my APM2.6 through mission planner. whenever i choose 'Nearly ALL' in LogBitmask , the readings of the 4 channels in RCOUT are flat, or the IMU is rubbish, but wh
Read more…Dear All,
I am developing UAV for Mapping. I use Canon Camera (SX260HS)+CHDK to trigger the camera based on time interval (intervalometer script) and based on distance (E38 script), both was working well.
Now, I want to use another brand of camera (i.e
Read more…I'm rookie in UAV. Where can I read Do and Don't rule for fly UAV,
Does the pilot need to be license to fly. Are law enforcement goring to arrest you if you fly without license.
What is the rule and regulation and where can I read it.
Thanks
Eddie
Read more…Hello Forum,
is it a big failure to calibrate the external compass(LEA6H) on a APM 2.6 V3.15 with an folded GPS-Mast and after this to fly with an upright GPS-Mast ?
Greetings from Stormy-Germany
Roger
Read more…hi, i have a quadcopter with APM2.6 , and i have a problem when downloading my logs from my APM2.6 through mission planner. whenever i choose 'Nearly ALL' in LogBitmask , the readings of the 4 channels in RCOUT are flat, or the IMU is rubbish, but wh
Read more…Bonjour quel est cette information (encadrée rouge)
The latest version of Mission Planner version 1.3.17 Terminal connects fine to my new pixhawk, but the "setup" menu contains:
reset
show
set
esc_calib
and the "test" menu contains:
baro
compass
ins
optflow
relay
shell
rangefinder
but no "motors" test. So how can
Read more…Greetings all,
Well my Tarot TL8X bit the dust, literally. Spiraled out the sky from about 60 meters. I had logged about 2 hours of 4-7 minute flights over the last few weeks. On the day of the crash, I flew it twice before without a problem. I
Read more…Hey guys I am looking at ways by which the range of battery operated UAVs can be extended beyond the normal 1-3 hours of flight time(or the 7 hours by the Techpod).
I have been looking at these guys http://www.amicell.co.il/batteries/rechargeable-bat
Here's my issue, I am unable to get the flight mode to change with my spektrum dx8, on the radio calibration page I see that channel 5 is working properly with the gear switch and I have set up flight modes, but when I switch from different flight mo
Read more…Hi,
Will the antenna Tracker code run on an old 1280 Oilpan type APM, and where can I get it?
Read more…So I think my octocopter had a brown out, but the question here is if I did have a brownout is it the autopilot or the power module? And how do I have out in the log files?
Thank you for any help.
Read more…Hi,I have just bought an APM 2.6 and use Futaba T10J radio, so I also bought a R3008SB Rx. I have read a lot about problems with the PixHawk and Futaba Systems. Is the APM 2.6 compatible with the R3008SB Rx? Do I need to purchase a PPM converter?Than
Read more…Does anyone see a problem with using an XT90 Anti Spark connector in a X8 with as 6 cell power supply. My concern is doing damage to the Pixhawk and RC with the initial connection through the resistor.
Thanks
David Ardis
Read more…