Hi,
I'm trying to set a Pixhawk with dragonlink and Dx8 for adruplane. After connecting everything I realized the channels need to be remapped (Went to Full parameters list, then entered 3 for RCMAP pitch, 2 for roll, 1 for throttle and 4 for Yaw).
An
Read more…I can't seem to get my S100 to take pictures much faster than an expourse every two seconds or so. I'm using the "trigger by distance" method to trigger from the autopilot. I think I've disabled all the camera features that might slow down the camera
Read more…Hi Guys,
First of all, I really want to say that 3dr is a great company, my first pixhawk was faulty after 1 week, they took care of everything even paying costs to send it over (which was a lot since i live in Europe) and even the possible import tax
Summary: Ardupilot 2.6, Mission Planner 1.3.9, last firmware, Mavlink connection, all worked as it should…few hours later, Mavlink won’t connect, uploads different firmware, tried older software - no good results, tried older firmware – Mavlink conne
Read more…Hello,
I have not flown my quad in couple weeks. I installed a new gimbal and went flying today..
The quad was very erratic. I even tried flying it with the gimbal completely plugged out and power off. Did not fly confident at all.
I noticed one of the
Read more…When I look at the tlog I see totally different maunders for the 3DR radio rssi than I see on the MP playback display. What’s the conversion formula to convert from mavlink rssi to percent? Most missions I see between 60 and 170 in the log but mostly
Read more…Hello everyone:
Only after reading the page ArducamOSD I learned that I could not connect if minimOSD pixhawk was connected by the USB port. I did and after that the letters are blurred or not seen anything. I will have destroyed the osd ???
Thank you
Read more…hi
September 11th day yesterday on a flight with my mapping quadcopter with pixhawk mapping and arducopter 3.1.5.
the quadcopter at 2 minutes into the mapping mission began to spin like crazy
continued to try to regain control passing quadcopter m
I want to connect my landing gear servos to apm.please inform me how to pin my wires to apm.
Read more…I notice mission planner has "Antenna Tracker v0.1" in the firmware list. Anyone seen documentation for this? I seem to be struggling to find anything.
Cheers
Si
Read more…Hello
I have been modifying arducopter code (2.9 and 3+) for awhile now and just recently ran into issue with the bootloader on several apm 2.5 boards. I use linux for development so I use command "make upload" to upload the hex files. On all three bo
Read more…Yesterday I was test flying a quadcopter with an APM 2.5 board. All seemed well and just as I was about to start flying a circuit, the quad listed to the right front slowly and it seemed like I had no control. It naturally flipped upside down just be
Read more…I am sure this is posted somewhere but I can not find it if was posted.
How can the PixHawk beeper be activated via the remote control?
Thanks
Read more…Hi,
I am trying to setup CAM_TRIG_DIST in arduplane but there is no CH7_OPT available.
My device, an arduini mini, works fine if I use signal pass-through to the axillary channel but it doesn't get triggered with CAM_TRIG_DIST.
Thanks
I am using PIXHA
Read more…Hello to all! I ais a problem with my arducopter 2 .6. He it in the red light flashes and which then remains red. And when I connect him(it) to mission to smooth an error message to apparrer by saying
Bad gyro Health
Here is if somebody can help me I
Hi Guys,
I am using the PX4 FMU V1.7.2 with IO V1.3.1, QGC 2.0.3beta, the latest QGC firmware, Quad with 4 x 40A SimonK firmware ESCs and 2815-470KV motors.
The installation/setup was straight forward, the firmware was updated smoothly, the RC and sens
Read more…Hello everyone,
Seeing in Ardupilot PARAMS, I found that it possible to adjust MAX RX rssi value and set a RSSI_PIN for load rssi value.
I have several legacy Thomas Scherrer LRS systems working on now with ardupilot. My rssi values are between 0,5 –
Read more…On first, sorry if this is not the correct place for post this. Too much changes in Ardupilot world since my last post on DIYDrones @2012. So please be patient, my English and ilusion is actually very lazy due a long illness those two past years...
I
Read more…Hi,
I am having problems arming my quad. I am using APM planner with a Turnigy transmitter with er9X firmware installed. I reset the ESEs and all of the motors powered up. I can configure and save but I cannot arm the copter have used throttle down
