Hi,
1. Is it possible to commence the autotrim procedure without radio switch, can I use some mission planner button to save the autotrim levels?
2. Is autotrim possible to set up to another channel than CH7?. Can I use CH6 for auto trim?
Read more…Is this a throttle percentage change or m/s change? I know I could go out and test it but it is -11F outside. Too cold to fly.
If assumptions are made it would be meters/second since the available range goes beyond 100.
Last time I flew I bumped it up
Read more…Hello guys,
I was wondering what would happen if a thermopile equipped attitude reference system goes into a cloud.
Is cloud opacity to IR high to the point where the system can no more work?
Cheers!
Read more…So I had 3DR put on a MiniOSD on the X8 that i just got and it works. But the problem that i am having is I can't connect to the OSD with the Config program it keeps saying Failed to load bootloader I want to customize the display and I can't do it!
Read more…Dear Everyone,
We are a team of aerospace and computer engineers based in San Juan, Puerto Rico. Like many of you, we are passionate about RC Aircraft and UAVs, and have enjoyed this hobby for more than 15 years.
For a long time we have committed our
Read more…Hi,
is there a possible way to combine two flight modes into one?
E.g., i fly acro mode and put my hands away from gimbals, copter switches to position automatically.
Is there a possibility to combine that for testing?
regards
Frank
Read more…I am working on a variable pitch quad design and I am running into some trouble tuning it. I have worked on the PIDs and got it to the point where it does not oscillate so that I can fly it. Here is a video of a test flight https://www.youtube.com/wat
Read more…Hi All,
I took a flight today with my giant copter, I found 2 of the motors were not responsive.
I tried to spin the motors using simple motor spin test using CLI test in Mission Planner.
'Hear' the motors twitching, when they want to break free to rota
Read more…I was recently flying my Tri in AUTO mode, flying a mission I had previously flown the day before, when to my horror it appeared to go completely nuts before free falling 100m to the ground. On review of the video from an onboard gopro you can clearl
Read more…Hi Im wondering is anyone out there could offer me some help. I have a DX8 Spectrum Remote for my FPV setup and I have built a dome camera set up so full pan and 45 degree downward tilt. Now I want to know if I can either use one of the Aux switches
Read more…Hi,
My dog thought my PX4 was delicious and chewed my IO board (he immediately regreted and gave it back to me in two pieces though...).
It's hard to find the IO board at the moment (I'm in the Netherlands) and I'm thinking of using the FMU itself with
Read more…Hi,
In arducopter I am used that arming is done by moving the rudder stickk to the left for a few seconds.
I am using arduplane now on a delta wing, the rudder is not even connected... How do you arm it?
I didnt see it mentioned anywhere in the manual.
T
Read more…Hello all,
I had a frightening experience with an APM 2.5 today that I was hoping some could shed light on. The quad ended up heavily damaged, but more importantly it went out of control and could have flown into others at the field. We are trying to
Read more…Hi all,
I was flying around and experienced a radio failsafe. RTL was engaged for one second and seemed like all motors were cut off while in RTL. Failsafe went away & stabilize kicked in very quickly, but my full throttle was not enough to recover -
Read more…Hello,
First of all I am electronic engineer and I almost loose my hair trying to solve the no fix with my GPS.
Controller:
Hardware: APM2.6
SOFT. arducopter 3.01
GPS: 3dr Ublox with compass
Multirotor:
hexacopter with T-motor
6 ESC 45 Amp with 3A 5V Bec
Carb
Read more…All has been going well since I did Autotune earlier this week. When flying my Quad 2 days ago in High winds ;20mph, gusting to 26mph , all was going well until the last RTL. I was ABOVE RTL altitude, engaged RTL, copter started to descend, then - I
Read more…Hi all,
Does anyone know what senseFly have done to allow for more control over the Canon P+S cameras they use?
You can see here that they have made some sort of hardware hack with a plug that connects to the flight controller, but not via the USB por
Read more…Hi,
I have recently purchased a APM 2.6 and running the latest Arduplane software. I have noticed on both the 'alpha' release of APM mission planner and Qgroundcontrol I only have basic information on the primary flight display. I have seen screen sho
Read more…