Hi,
My dog thought my PX4 was delicious and chewed my IO board (he immediately regreted and gave it back to me in two pieces though...).
It's hard to find the IO board at the moment (I'm in the Netherlands) and I'm thinking of using the FMU itself with
Read more…Hi,
In arducopter I am used that arming is done by moving the rudder stickk to the left for a few seconds.
I am using arduplane now on a delta wing, the rudder is not even connected... How do you arm it?
I didnt see it mentioned anywhere in the manual.
T
Read more…Hello all,
I had a frightening experience with an APM 2.5 today that I was hoping some could shed light on. The quad ended up heavily damaged, but more importantly it went out of control and could have flown into others at the field. We are trying to
Read more…Hi all,
I was flying around and experienced a radio failsafe. RTL was engaged for one second and seemed like all motors were cut off while in RTL. Failsafe went away & stabilize kicked in very quickly, but my full throttle was not enough to recover -
Read more…Hello,
First of all I am electronic engineer and I almost loose my hair trying to solve the no fix with my GPS.
Controller:
Hardware: APM2.6
SOFT. arducopter 3.01
GPS: 3dr Ublox with compass
Multirotor:
hexacopter with T-motor
6 ESC 45 Amp with 3A 5V Bec
Carb
Read more…All has been going well since I did Autotune earlier this week. When flying my Quad 2 days ago in High winds ;20mph, gusting to 26mph , all was going well until the last RTL. I was ABOVE RTL altitude, engaged RTL, copter started to descend, then - I
Read more…Hi all,
Does anyone know what senseFly have done to allow for more control over the Canon P+S cameras they use?
You can see here that they have made some sort of hardware hack with a plug that connects to the flight controller, but not via the USB por
Read more…Hi,
I have recently purchased a APM 2.6 and running the latest Arduplane software. I have noticed on both the 'alpha' release of APM mission planner and Qgroundcontrol I only have basic information on the primary flight display. I have seen screen sho
Read more…While I am new to Arduplane/APM I have been flying FPV for several years with autopilots/pilot assist units. I have been playing with waypoints and AUTO mode and have become concerned about fly-away possiblities if I mess up....the one of the intende
Read more…Hi everybody,
excause my english....
Does anybody has expirence with this kind of Batteries..?
I just bought 4 of them each one 3.2 Voltage 3A. That means i put all of them in series to get
12.8 voltage with 3 A.
I use a H-Copter and hape to get a liitle
Read more…which website is alternative in quality so i can buy from because 3dr out of stock now
i found it in this website
http://www.thanksbuyer.com/px4fmu-autopilot-flight-control-management-unit-multicopter-flight-control-with-px4io-board-and-buzzer-25620
is
This question is not a how to type of question but more of a will it work. I have an EZUHF system for my copter and goggles so i can FPV. However there are a lot of cables about me particularly connecting the antenna to the goggles. Also i have notic
Read more…i want to know how to connect an external osd like minimosd or any other to the px4fmu or io board
what if i want the data also to be sent on the video link in the same time with the telemetry not the telemetry only
please explain to me how
Anyone bought this (or something like it) yet and willing to share some lessons learned?
http://www.fpvflying.com/products/FPV%252d10X-zoom-camera.html
Read more…I am trying to re create a second APM. I want to load 2.74b so that it is the same as my first. In mission planner, I tried to get previous versions. The list started with 2.74 ( is this the b version ?). After loading 2.74, I ran the CLI, it repor
Read more…https://www.agronomy.org/story/2013/nov/tue/improved-crop-monitoring-takes-flighthttp://Way to go Jim...
Nice article on drones in ag
Dean
Read more…I'm thinking about setting up a 3DR Quad Frame for heavier lifting than the standard setup.
Read more…Anyone else having this problem?
I have a dataflash log (5mb+) which seems valid, I can graph it and see all the values and the track on the map, but the KML files it generates are empty other than the waypoints, empty GPX files too. No error messages
Read more…Hi,
I'm trying to configure failsafe on my APM 2.5 and I configured my frsky receiver to go down to 985 (minimum sent by the radio is set to 1015 otherwise when throttle is at 0) on the throttle channel when in failsafe and auto land mode.
While bench
Read more…