Quality Motors
Hey guys..
Just wondering, if price is not an issue, what is the best motor you can buy for a heavy lift octo setup.
/M.T.
Read more…
4 Replies
All Discussions (17281)
Sort by
Motor Selection
What difference would be noted between using a 800Kv to 900Kv motor (Tiger T-Motor MT2216-12 vs T-Motor MT2216-11 ) on the exact same frame and using the same 12.45 props? I mistakenly bought the 900s but thought to try them anyway.
I currently use th
Read more…Dronecell SIM900D not sensing the sim card.
Hi all
Im trying to get my dronecell up and running.
i have connected the cell through TX0/RX0 Ardunio 2560. Serial connections is working.
It respons to my AT command, but during startup it throwing CPIN NOT DETECTED.
I belive it not sensing the sim car
Read more…Help – Why did my copter just keep climbing?
Hi. - Happy new year.
Im new to copters but have been using arduplane for a while.
I have been setting up a new quadcopter and following Dave Cs guide. Its flying very nicely in all modes and I have done a few auto missions around my field.
Before th
Read more…No output from APM2
I will fit my ArduPilot 2.0 in my nitro powered trainer.
I set up the ArduPilot as on this video http://youtu.be/Q9xSeXOi4ig
Basically battery to receiver, then aileron and 3 position switch (Aux 2 on my DX8) from receiver to ArduPilot, and servo plug
Read more…Kangaroo Crash
I decided to go for an early morning flight with my 3DR quad this morning to try for a few shots of kangaroos. Well, on the first attempt I got a bit too close and crashed. But the footage after it crashed is just fantastic. I couldn't have scripted
Read more…does it possible to have a mission planer on android phone and use 3drradio???
now that almost everything is good on apm 2.5 i think it will be perfect to have an option to use android phone screen to have mission planner for example
do you know if there will be this kind of option?
Read more…Waypoints without mission planner?
Is it possible to set waypoints from the TX? For example, fly to a point, hit a switch on the tx to mark first way point, fly to a second point, hit a switch... etc?
Read more…Quadcopter frame design: is square or tube better to reduce vibration? Aluminum or carbon fiber?
I may have missed previous posts, but could not find a definite answer concerning Quadcopter frame design: are square or tube type arms and/or frame better to reduce vibration? Which is better when it comes to vibration: aluminum or carbon fiber?
Than
Read more…Public Liability Insurance in Australia
I've been searching through the forum looking for information on insurance, specifically public liability, and have found some interesting information but nothing specific. I hate to bring up the topic but I'd like to do some aerial video of building
Read more…GoPro 3 Gimbal that fits on a 3DR Hexa-B frame?
I'm looking for a camera gimbal that fits on the 3DR Frame and can hold and stabilize a GoPro 3. I'm looking to use this setup for filming aerial shots for a number of short film projects.
Can anyone recommend anything on the market? I have done my o
Read more…Dome on a Drone part deux
I have a 3DR quad ready to go except I needed a dome to protect the electronics. I didn't want to take time to make one so I was searching around the forum for a ready made one that would work. I saw Robert Lefebvre's thread on his big aluminum frame
Read more…GPS cable
Is there a JST 6 cable to DF13 6 cable. When using the Bixler case the JST cable is hard up against the side at 90deg exit. Mine just broke. Now when you add the new case it there isn't enough room for even that.The DF13 cable is a better gauge so le
Read more…Hover with a 3D acrobatic plane?
Does anyone know if it is possible to create a flight mode for ArduPlane to prop hang. I am currently using a 3d acrobatic plane to work out any bugs etc before moving to a more UAV style plane. My idea is if it possible to set up a flight mode "hove
Read more…Is it necessary to (update)flash the Atmega32U2 (PPM encoder) on an APM 2.5 if using a Futaba system?
I'm constantly expanding my understanding of all the options and systems within the APM 2.5 by re-reading the wiki and looking for things that have changed or things that I hadn't considered before.
One thing that has recently caught my eye was the se
Read more…V tail problema
I've bought a apm 2.5 recently. My question is: APM 2.5 support V Tail for a sailplane?
Read more…Extending the ABC LEDs with external LEDs
Is there an easy way to replicate the ABC status lights with external LEDs? My board is buried deep in an enclosure and I need to see the ABC status lights using external LEDs.
Thanks
Read more…APM2 / 2.5 LEDs
There's been a few threads on LED strips and lights on the ARDU but most seem outdated now,
What is currently available at V2.8/2.8.1 out of the box (as it were) are any of the analogue pins already assigned with LED outputs ?
Read more…Programming with Arducopter/Arduino
Hello,
I would like to compile and upload the Arducopter code to my UAV. To do so I followed the instructions on the wiki, that is :
-installed the Arduino 1.0.3 (Arudpilot) version on win7
-installed the 2.8.1 software version (the two folders Arducopt
Read more…Airspeed Sensor Normal?
Hi folks,
I just installed an airspeed sensor on my new APM 2.5.. I have enabled it in mission planner and it seems to be workig well? But when I click on enable airspeed the horizon pitches up and down depending on the airspeed reading, so if I blow
Read more…