Dear all,
If someone was interested in manufacturing multirotors to sell in RTF form using the Ardupilot board as the flight control, what would the hurdles be?
Obviously, the ardupilot board would have to be tuned to the frame being sold, and this cod
Read more…Hi,
the current Pin12 for 3DR Power Module in the mission planner to put only on the extended list. In the standard List i can set only PIN A2
Uwe
Read more…tried the mission planer away from any internet access and unable to use it can anyone ?.
if so how it had no firmware available and no google maps am I missing something.
Read more…Hi folks, I had to buy a skywalker 1900 after I stuffed my original 1500 into some trees. Does anyone have a good, solid param file for their 1900 that wouldn't mind sharing? This would be tremendously helpful :)
spag
Read more…It might be affordable and easy to create a wooden 1/2-model of a multicopter frame and then vacuum form 2 identical pieces and attach them together so that it will make a multicopterframe. It could be done with transparent material also? Little elas
Read more…Hi guysRecently A friend Louis and I bought a complete APM 2.5 setup for x8 flying wingsAPM 2.53Dr radio 433 MHzUblox / Mediatek GPSAirspeed sensorAnd the 3DR power module , we completed our setup and started testing the configuration for elevon setu
Read more…Hi,
I just have another problem with my Hexacopter and APM 2.5.
When I connect the two servo cables of my camera mount to pin 11/10 and set it up in the mission planner the servos are moving like they should. But only for just 1 or 2 seconds. Thereafte
Read more…Hi all,
For some reason I just cannot get any data from my APM2.5 via xbee. Never had any troubles with APM2.
I am connected to the "new wireless port" on APM2.5 via a UartSBee breakout. The two XBee's connect to each other, no problem, however I am r
Read more…I was hovering my quad at a fairly high altitude when it suddenly tumbled out of the sky into a 50' tree. I assembled a huge stick and got it down. I was flying while it was snowing... possibly a bad idea...I was about 2 minutes into the flight. I th
Read more…I am running the latest version of MP (1.2.28) and am getting some strange behavior.
When I connect to my APM (2.5) and refesh the parameters it goes ok. Once the parameters are loaded the screen goes into a repainting loop as it tries to display. T
Read more…
Hi.
Just wondering if anyone else has a similar set up to mine and can share their PIDs /parameters.
I have these motors on a quad.
I was flyin
Read more…Hi All,
I have a strange problem ( at least strange for me).
First off all i am newbie and i just bought apm 2.5 kit. I installed on the plane as you can see at attached picture.
I powered up plane connected to mission planner and make a Manuel levelin
Read more…Hi there,
I have a problem with my 3DRobotics ESC's on my Hexacopter.
I want to program them with a super soft start mode.
Everything works fine till I exit the program mode and replug my battery.
They haven't learnt what I programmed into it and start a
Read more…Hi Peeps,
I just got a AMP2.5 to play with, hoping to use it for several projects such as a camera gimbal controller, a multicopter and possible use it in a plane and boat too :)
I managed to connect over USB only and set it up for a quad firmware, I c
Read more…Can anyone tell me the explanation of “RC1, RC2…RC8. Are they referring to the APM channels, 1 thru 8???
Any help will be appreciated
Thanks. Brian
Read more…Hi,
Sorry this is actually about the APM1 shield; I found no category for that.
Is there a 3.3V logic level SPI bus somewhere on it? I have an MPS5611 too many, and I might as well use it there if possible (with a few code mods I know).
The schematic ..
Read more…Hi,
I just finished building this H frame quad, entirely in aluminium, and I'm now trying to find the best compromise as for battery/ESC/motor to make the beast flyable.
I do not have any clue at the moment on how to choose these properly, nor really s
Read more…Can anyone help me find the cause of the only two crashes I've had with my FPV Raptor and APM 2.5.
I've done a dozen or so auto take offs successfully, but two of them resulted in crashes. Actually in both cases I recognized things weren't going well
Read more…