I was hoping that someone might be able to provide me with a UBlox Binary file from a flight. I want to try to run differential processing on it using PPP to see what kind of accuracies I can get in the forward and reverse solution using GrafNav. An
Read more…Hello,
2 days ago I upgraded my APM 2.0 onboard PPM enconder with the version 2.3.15 (it seems all working ok).
It was in downloads section (ardupilot mega or arducopter repository, I'm not sure) but now it only shows version 2.3.13
Does anyone knows wh
Read more…The title says it all, this gps in in brand new condition, i was sent two by mistake an was allowed to keep it, i tested it on my multiwii pro flight controller with RTL and it worked great.
I can also flash it with any fimware you like just send me t
Read more…I have a strange issue at the moment, my quad will be set onto RTL and on the way back it will randomly spin on one axis eg: the quad rotates once around front rite and back left prop, by rotate i mean it literally rotates 360 degress, first 180 deg
Read more…Suddenly I can't connect to APM2 with the Mission Planner (v1.2.29).
It starts getting params fine but then halts with this:
I have erased and reset to no avail, what's going on??
This is the error from the MP:
Any ideas?
Hi guys, I have a couple of spare GY-80 lying around here (this is a chinese board with gyro, accel, magn and barometric sensors) and a Arduino Mega. With those I want to make my own ArduPilotMega :)
I have a computer science degree, so coding isn't a
Read more…APM is an amazing piece of hardware and software. i was very impressed to see the prcise naviagation the aircraft does. To get precise navigation and stabilization the aircraft should be very well trimmed in manual mode by making long duration flight
Read more…Hi, I am wanting to run the ARDUPLANE Board in RC plane, and use the data from that via Mavlink to show the realtime flight on X-Plane.
I can get the RC TX to control the X-Plane, but what I want is for the X-Plane to just look at the Raw data, GPS,
Read more…Hi I was wondering if it would be possible to have the forward and aft copter blades at different heights to the sides. My chasis at the front (top) blade is lower than that of the rear (bottom), think copter blade at the nose and wing of an osprey.
Read more…Was out at the hobby store to see what i'm sure everyone has heard of before, the gaui 500x and it doesn't look that bad. But I do have a few quick questions before I bite the pricey bullet. A. are there any other almost ready to fly kits that pac
Read more…I had to cut the transparent heat shrink tubing on my ESCs (HobbyKing 30A BlueSeries) to reprogram them with SimonK firmware. Everything went fine, but now I'm looking for a solution to replace the original heat shrink tubing that was over the ESCs.
Read more…The following topic is to discuss how we can use our drones for the good of other people. ideas rang from fighting crime, search and rescue, ect... any ideas or topics can be started here.
Read more…I have been trying to get the autoland feature working for a couple of weeks now to no avail? The first time I made a flight plan with several waypoints and then a final LAND command where the plane would reach and then stall, on the second attempt I
Read more…Need Some Help Here, I Have A Neo-6m And It Is Misbehaving, Everyday I Have To Connect It Directly To My Pc Untill It Gets A Lock, If I Do Not Do This, I Will Not Get a Gps Lock ?
My theory Is The Gps Has No Internal Clock So Come Midnight It Cannot
Read more…Hello! I need to use UART 2 for telemetry on APM 2.5 so that I can use both USB(multiplexed with UART0) and Xbee telemetry(hopefully on UART 2). I have followed the directions given on the google code page, and this is what I have done.
-Cut the two u
Read more…Hello, i have a quadcopter with the arducopter 2.5installed, i have had two crashes so far, both occured because of signal failure.
Has someone made a software tool yet to set the ardumega to RTL on signal failure?
i would greatly appreciate the help a
Read more…Does the APM code include a possibility to add additional temperature sensors to the system? It would be nice to have live temp readings from ESC, motor, battery and so on.
Perhaps LM35 sensor could be used:
The LM35 is a precision temperature sensor,
Read more…I have been trying to get 2.9 to build so I can beta test and I cannot get it to compile. I have followed the Wiki and other instructions, but when I try to build I get a huge list of errors - most of which appear to be around variable declarations.
Read more…Hi,
I'm looking for someone that can make a nice composite airframe, like the penguin-B but not so complex of course. I made a 3D rendering of the Mugin and a nice composite version of this airframe would be enough for me. Its for an UAV in my country
Read more…Hi!
In Mission Planner, one can load do "Tlog > kml or Graph", then if you go to "Graph Log", there will be a bunch of variables to choose from after selecting a particular Tlog. If I chose roll, then the Mavlink Log Graph will update with the relevan
Read more…