Quadcopter fpv with machine gun
This isn't real, is it?
https://www.youtube.com/watch?v=SNPJMk2fgJU
Read more…
1 Reply
All Discussions (17288)
Sort by
apm hitting ppm failsafe mid flight
My skywalker's apm tends to crash after a running for awhile. the airlerons lock at a certain angle, the rudder deflects and all of it leads to a spiralling crash. I can't understand why suddenly the power goes off to the board, (the imu lights go of
Read more…Can acceleration in global coordinates be calculated and exported via DCM?
For a rover application .....
I am modifying the 1.9 firmware to send out acceleration in global coordinates, but I am not getting satisfactory results.
My process is to perform a matrix operation by multiplying the acceleration vector (in body frame)
Read more…Is APM2 avilable in some 3d format?
Hello all
First of all I want to thank all of you for this great forum.
I know this question has been asked before but is there avilable a 3d model of the APM2?
I am designing my quad in Autodesk Inventor and it would be great to have a 3d model in ther
Read more…gps issue solid blue light and flashing red
hi,
after have been facing a loiter mode issue, i ve discovered that even the blue light on the gps is solid, the red light on oil pan still flash, unless i connect it to the apm.
is it normal behaviour?
if not, what should i do?
thx for helping
Read more…loiter mode holding nothing and always the same way
hi,
today i ve tried the gps hold and it was quite weird.
everytime you enable it, it hold for 2 sec, then aile left on 10 m then ele and go away.
i ve check on my apm if it s loiter mode and not something else, and it is loiter mode that is enable.
here
Read more…3DR RadioTelemetry Kit-915 Mhz
Hi!
When will it be available 3DR RadioTelemetry Kit-915 Mhz?
Would have to be urgently.
Can someone help? ?
Joe
Read more…Ardupilot board APM 2.0 received with 3.3 V not weld aligned and JP1 PIN not welded. GPS 3DFIX unstable
Hi,
I'm very pleased to join this Forum. I'm a newbies using Ardupilot APM 2.0 and after a long long weeks awaiting my board, I have received it, 2 weeks ago !!! Ordered on january.
I have discovered problems on JP1 PIN weldind and 3.3 Volts CMS not co
Read more…Landing gear camera mount info
I'm looking for a setup ideas for landing gear / camera mount. something along the lines of the X468 or droidworks copy type or others too.
wanted to see what others find that i might not have. found one setup that looked like the first landing gea
Read more…How many number of analog pins does APM 2.0 have?
According to the DIYdrone website, APM 2.0 should have 12 analog pins. However, when I tested it out, only A0~A8 which corresponds to 54~62 work as analog pins, but the rest 3 pins do not work. I tested this with an airspeed sensor. The following cod
Read more…APM2.0 with turnigy 9x radio / Switch mode setup a nightmare ?
Just recieved my APM2.0 board. Very pleased I might add !! ... delivered to France in under 48 hours !
I have the Turnigy 9x radio with latest ER9X firmware. I have been setting up the APM today, nice and simple, no problems.....Until...I wanted to se
Read more…PID Tuning configuration not shown
Hi,
I have updated mission planner to v1.1.75, and when I tried to tune PID in the configuration window, I see it only allow me to configure radio, sensors, etc, but there is no PID configuration window.
Anyway, I have connected APM to flightgear, and
Read more…MP 1.1.75 Still not "talking" with apm1
Hi Guys
I been having trouble getting my apm1 to connect with the MP. Just upgraded to 1.1.75 this am but I'm still having this issue. However I've found that with 1.1.75 if I "wake up" the apm with the terminal mode, MP with then connect in the norma
Read more…ArduPilot LOITER and AUTO problems
Hardware:
- EasyStar
- ArduPilot
- Airspeed
- Thermopile
Software
- ArduPilot 2.7.1
Hello,
I had a old Ardupilot laying around for two years now. Last week I assembled everthing an did my first flights.
I copied the AP_config.h and modified it just a little bit(CH_MIN/
Read more…Confused about Compass Calibration
I just got my quad fly and am trying to figure out all the Compass parameters.
COMPASS_AUTODEC by default this is one. After I fly should I see a new value in the COMPASS_DEV parameter?
COMPASS_LEARN what’s that and how does it work?
There are three l
Read more…optical flow and flight modes
hi everybody,
i just installed the optical flow, and i wan ted to make sure certain point.
when you enable optical flow, is used when you enable alt mode?
Is it used when loiter mode is enable too?
what is the max height for that kind of sensor to work?
t
Read more…OSRC
Finally got my hands on this nice piece of kit and flew my f1 with APM-2 stabilising the camera.https://www.youtube.com/user/OpenSourceRemote
Read more…How load .pde file using mission planner?
hi,
well it s all in the title, is it possible?
thx for help
herve
Read more…point to multi-point
will these radios do point to multi-point ? I need two diferent ground stationd to track the balloon.
Earl
Read more…Tricopter PID`s Help
Anybody had any success with APM2.0 and a Tricopter? after much messing around with PID`s I can get it to RTL in a fashion 70% of the time but once it gets bak to Launch it tends to lose it bearings and dissapear in another direction and I have to sw
Read more…