How do I back up MTK 3329 firmware it? I can download to upgrade the software, but there is no backup
http://code.google.com/p/ardupilot/wiki/MediaTek
May I ask who can provide the following MT3329 5HZ 38400 firmware it? Thank you very much。
I have u
Read more…My Arducopter RC2 turned off all four motors at about 100' up today, and plunged to its death with no rotors spinning.
I believe there is a software bug or misguided feature at the root of it.
I was using GPS Hold to pin position, and the Arducopter
Read more…Hello Good Day Eve or Morn
Shane if you find this and are already on board with Jeff A. and others on the LGS welcome
If not, lets get up to speed up to speed.
To all others; welcome
to be sure input and colaborations will be invited and needed.
This
Read more…Hi everyone,I've written a patch for APM that allows for the autopilot/IMU shield to be placed in any arbitrary orientation relative to the airframe. The patch (based on current trunk code) basically contains the code to add Euler angle offsets to th
Read more…Hi,I am going to test flight a funjet with the APM, are there any suggestions for PID settings for the first flight with a funjet?Thanks.
Read more…I killed my one battery. I have ordered others, but they are not here yet. They are 11.1v Li-pos
I have a 12v power supply that can supply 10A +. Can I run the system via that till the batteries get here?
Read more…Hello everyone, I need help. I've been building a quad using the Arducopter manual and forums as a reference. I am no expert, but I do have some experience using ArduPilot Mega/IMU on several planes. I have also built and flown a Tricopter, so the
Read more…I cant seem to find the system requirements for the Arducopter configurator tool in the forums or on the wiki. I have windows 7 starter on my netbook and it says that the configurator is not compatible with this version of windows. Do I need to go
Read more…My battery specifies 28C, how many amps should my charger be set at? I have a thunder t6 charger and i set it to 3S and the default 0.1A.
Also, if anyone else has this charger could you tell me what the number displayed at the lower right counting up
Read more…Is it possible to have 2 motors driven by the same signal? Could I create an octo on the current setup but just double up on the motors driving each adjacent pair by one signal? It could fly in a configuration so 2 motors form the front side (side by
Read more…Hi,
just would like to know if there is a way to connect the new Futaba S.BUS receiver via serial bus to the APM?
regards,
Peter
Read more…
Hey, another noob question, but, if it prevent 250$ investment!
I receive my APM and APM IMU yesterday, solder everything, make a couple of test, working great so far. Now, I am at the point to put it on my quad copter and I'm worried about power di
Read more…Hello.
I'm building and programming my own UAV using an Arduino Duemilanove. Yesterday I made a leap and the board is now controlling the servos and with fake position (no GPS connected yet) it tries to turn the plane to the right direction.
The maid
Read more…Dear all,
I'm considering to build a Arduino/GPS+someting device to have precise feedback about about Velocity and Velocity Made Good on my catamaran. The boat is a small hightech catamaran :
http://dnacat.blogspot.com/2011/01/bundy-pics-by-carolijn-b
Read more…It appears that the IMU is out of stock everywhere and has been for a bit. When will these be back in stock?
Thanks
Read more…
Hi,
I have interfaced Freescales 7620 3 axis accelerometer and am getting the readings properly.
Now I have difficulty in understanding the readings, If it is mounted on table stationary, then the X,Y read 1.65V (0g) and in Z axis 0.85V (-1g)
Read more…I have assembled a new APM from the diydrones store and uploaded the newest code for Jan.3 (1.01).
When I have the APM/IMU installed in my Easystar, the PPM light flashes and the A B C light never go into a flashing state for calibrating the gyros.
Read more…Hi,I am new to UAV I have been playing for the last 3years with model helicopters.I have just built and started flying a mikrokopter octo.I would like to know what is the best type of quadcopter for aerial video and why?Many thanks in advance to your
Read more…Hello everyone,
I have an ardupilot mega that I'm powering with a 3cell 2500mah battery, through an ESC. the ESC is outputting exactly 5v. I've followed the instructions in the manual to setup the voltage sensor. I soldered 3 of the 3.9k resisters in
Read more…is there plans to support more than 6 ppm output for using more escs? would it be something solved in a future code release or is it sois it something that will be solved in a future code release or is itsomething to do more with the hardware ? plan
Read more…