Hi
After doing a façade data collect (bunch of images) is there a UgCS software utility/package that can generate a map or grid of the collected images? Once a collection has been done and analyzed, if needed, I'd like to be to send the drone to a pa
Read more…Hi
I'm thinking that Joystick more or Manual Mode would be the way to do this. I'd like to fly the quad, have the flight path captured and saved so that it can be reloaded and used again automatically. Are there tutorials or more directions available
Read more…Hi
Is it possible to run the UgCS app on an Android Device Emulator? If so, are there preferred device emulators to use?
Read more…Hi
In watching the Facade prep video, how are the multiple path created (both vertical and horizontal) at around 40 secs into the video?
Thanks...
Read more…Hi
I've installed UgCS for DJI on a DJI Crystal Sky. In connecting the Crystal Sky to the Controller and to the Matrice 210 RTK, UgCS for SJI says:
"CHECKING PERMISSIONS..."
If a few seconds this is then followed by a popup that says:
"Permission Check F
Read more…Hi
Is it possible to install the UgCS app on an Android device without setting up an account?
Thanks...
Read more…Hi, I purchased the Enterprise version of UgCS and I'm trying to use UgCS for a Pixhawk Rover(boat). When I spoke with Madara she said it was supported but not tested. There's not vehicle specific profile for rover in the program, is there a manual w
Read more…Hi
Can the UgCS for DJI app be used by an app I create from the DJI SDK (used like an import or included in the gradle script or Manifest file)?
Thanks..
Read more…Hi
I'm using Samsung Galaxy S2's for my screens with DJI's Mavc 2 Zoom and Matrice 210 RTK.. When about to install the UgCS fro DJI it has a notice:
"This app may not be optimized for your device"
Is this something I need to be concerned about?
Thanks
Read more…I received a trial license. But When I want to activate the license, it shows a message like: "Sorry, an error occurred during the license activation. Error call of activation service: 'Internal Service Error(500)'". (attached image)
The error message
Read more…Hello all,
I'm looking to find some help with figuring out what I'm doing wrong with my UgCS missions. I'm hoping someone can look at the mission and tell me what I'm doing wrong.
I've been able to create a mission, connect to the drone, upload the mis
Read more…Does anyone know if UgCS works with the Mavic 2 Pro or Zoom? I might need to get one in the next few days and I really need to know if it's going to work with UgCS.
Cheers,
Rob
Read more…Dear all,
I am trying to upload a mission to the aircraft and get this message:
"The GPS signal of the aircraft is weak"
Besides, I have 17 GPS, either in the UgCS for DJI and in telemetry.
Can someone help me?
Cheers,
Felipe.
Read more…Hello,
We are using a DJI M600 with a Ronin MX gimbal and an Android tablet.
When using the DJI app we can select between making the gimbal yaw and pitch using the C2 button on the controller, you then use the dial to move the gimbal.
If we then switch
Read more…I get this error when I'm planning very large missions (more than 1200 waypoints approximately) and trying to pair them down to a manageable size.
Once I get this error, I'm unable to remove routes from the program since they show up again after about
Read more…When AreaScan is used, UgCS places extra waypoints to keep the flight path at a constant altitude above ground level. However, once the route is converted to waypoints, this functionality is lost. There needs to be a way to either convert the waypo
Read more…Can someone tell me what's going on here? It usually happens when I convert an Area Scan to waypoints, or if I import a waypoint file. I have a 2.5 m resolution DEM loaded. It doesn't always do this, but it might correlate with the number of waypo
Read more…Hello,
Using a M210 RTK, is it possible to add the correction of the base position of DJI RTK differential antenna?
We use a GNSS NMEA base antenna to verify the DJI base error. We would insert this difference in order to save the right data on the EXI
Read more…I need to do scans over a large area (not a camera) and I need the lines from each block to line up together. Is there a way to create an areascan mission with a basepoint? This way, all the lines will start from a common location. The basepoint n
Read more…