"I have a Tx JR 388 (2,4 Ghz FRSKY) and Rx FRSKY D8R v2 with PPM at ch8. In JR channel order is 1Throttle 2Aleiron 3Elevator and 4Rudder, and I changed the reading order of the receiver in the code:
//ch1 =…"
Josu Berriatua's Discussions
Problem upload code to ArduIMU V2
Started this discussion. Last reply by Josu Berriatua May 30, 2011. 1 Reply 0 Likes
I'm new to the Quad, and I would appreciate help.I have V2 ArduIMU flat and I can not load the code. At first I could do it, (use Diydrones cable) and I tried several versions (1.5 1.6 1.7) and even…Continue
Problems Quadcopter with ArduIMU V2
Started this discussion. Last reply by Josu Berriatua Jun 14, 2011. 5 Replies 0 Likes
Hi, I'm doing a ArduIMU quadcopter with V2. I load Arduimu code without problems and HappyKillmore ArduimuTest is fine, but when I try the plate with a servo and transmitter receiver does nothing, no…Continue
Josu Berriatua's Page
Latest Activity
Josu Berriatua replied to Omar Achraf's discussion Ardu IMU V2"Hi Omar, what programs are HK and NI test? where they are?
Thanks"
Josu Berriatua replied to Josu Berriatua's discussion Problems Quadcopter with ArduIMU V2"Thank you very much for your information. I'll download your code and look to see if I can understand it and adapt it for me. I do not use PPM encoder. My RX is a FRSKY and gives me the PPM chain in the ch8."
Lenz Grimmer replied to Josu Berriatua's discussion Problems Quadcopter with ArduIMU V2"Yes, I had the same problem as I used a different method to convert the receiver signal into PPM values on my quad (using the Spektrum2PPM encoder from 1hoch4). My channels are assigned in the same way as yours are.
In version 1.15 of Jose's…"
Josu Berriatua replied to Josu Berriatua's discussion Problems Quadcopter with ArduIMU V2"Hi Lenz, i load the Jose Julio´s code (ver 1.15), but i think my problem is because in JR the order channels is 1 throtle 2 aileron 3 elevator and 4 ruder, and I can not change the order they are read, and the times of each in the…"
Lenz Grimmer replied to Josu Berriatua's discussion Problems Quadcopter with ArduIMU V2"Which code exactly are you loading? The regular ArduIMU code base is just that, an IMU. It has no code to read receiver values or drive ESCs. If you want to use the ArduIMU as a Quadrocopter controller board, you need to use Jose Julio's…"
Josu Berriatua replied to Josu Berriatua's discussion Problems Quadcopter with ArduIMU V2"After loading the 1.7 code so good on the test, but when I test the board in the quad does nothing. My radio is JR with 2.4 module FRSKY DJT and receiver of FRSKY D8R v2 with PPM sum on channel 8 (updated).
I think the problem may be…"
Josu Berriatua replied to Josu Berriatua's discussion Problem upload code to ArduIMU V2"Fixed. The FTDI cable was wrong. I have seen this to make a FTDI cable with that if it worked my plate. You can see how it is here: http://txapuzas.blogspot.com/2010/07/cable-de-programacion-para-arduino-ftdi.html
The construction cost is about 5$."
Josu Berriatua posted a discussionProblem upload code to ArduIMU V2
I'm new to the Quad, and I would appreciate help.I have V2 ArduIMU flat and I can not load the code. At first I could do it, (use Diydrones cable) and I tried several versions (1.5 1.6 1.7) and even worked the ArduimuTest then when connected to the radio (PPM) did not send signal to the ESC. After several tests now I can not load the code, because when click upload to arduino (see 0022) after compiling the first thing is to reset the board (LED yellow, red and blue blink and green fixed) and…See More
Josu Berriatua commented on Jose Julio's blog post ArduIMU Quadcopter part II (mini)"Hi, I'm doing a ArduIMU quadcopter with V2. Cargo Arduimu code without problems and HappyKillmore ArduimuTest is fine, but when I try the plate with a servo and transmitter receiver does nothing, no move to move the plate, and even when I move…"
Josu Berriatua posted a discussionProblems Quadcopter with ArduIMU V2
Hi, I'm doing a ArduIMU quadcopter with V2. I load Arduimu code without problems and HappyKillmore ArduimuTest is fine, but when I try the plate with a servo and transmitter receiver does nothing, no move to move the plate, and even when I move the levers on the transmitter. I tried to verions 1.5 1.6 1.7 1.81 and 1.8.2.At first I did not use GPS or barometric or magnetometers.Can anyone help?Thank you for your attention and sorry for my english.See More
Profile Information
- About Me:
- I'm build a Quadripocter with Arduimu v2 flat
- Tell us a bit about your UAV interest
- Arduimu V2 flat
Comment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
ArduRover User Group
183 members
-
ArduCopter User Group
1278 members
-
Andropilot Users Group
182 members
-
Moderators
24 members
-
Documentation Editors
51 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
