Hey there all you programmers!
I am not very good at programming, but I need to access the C++ code files that contain the flight modes for the Pixhawk. In particular, I would like to see the Fly-by-Wire Modes A and B (although access to all of them i
Read more…I just got a new Quanum Nova from hobby king and it flies ok but not as well as my other APM multirotors. I upgraded to firmware 3.2.1 and everything functions including Auto missions. The only hardware change I have made is adding a 3DR telemetry ra
Read more…Apologies if I missed an obvious discussion of this. I'd like to use LIDAR Lite to maintain a precision fixed relatively low altitude based on a reference altitude, irrespective of ground objects it passes over. So, for example, if the reference star
Read more…Hello,
Has anyone find a way to convert the data from the data flash files into timestamps with year/month/day and hour/minute/second information.
I'd like to extract the GPS and barometric altitude readings to manually tag some photos with. The camer
Read more…Hi,
out of sheer curiosity I'm often changing the flight modes.
Now I'm wondering what is the difference between LOITER and POSITION_HOLD modes?
Is there an advantage from one over the other?
Both work well holding the copter firmly in the air.
Am I missi
Read more…Hello, I have used Canon S100 as photomapping camera. But since it's discontinued, it's getting more difficult to find it on the market. I am looking for replacement in case I lose my S100 again (crash happens!), and find that Nikon P330 is comparabl
Read more…hi, since about two ot three beta releases ago I noticed that a lot of the full parameter list descriptions have gone missing completely, which were previously there....some of there are (not inclusive of all that are missing)
ATC_ACCEL_P_MAX |
ATC_ACCEL |
What are the best sensors for weather monitoring, remote sensing, human detection on DIY Drones
Read more…Is this 'Advertising' -To good to be true - for potential investors??
Read more…Hi,
I recently discovered a post on RCG here back in May 2015 from a new member about using a single Pixhawk for VTOL control on the BirdsEyeView FireFLY6. It lead to the PX4 page below describing some development firmware for the Pixhawk. Does anyone
Read more…Hi – can I request some help with my home built 680 Pixhawk controlled quad please. Sorry if I’m not in the correct place in this forum.
The craft has done several autotunes and in some ways seems to fly ok however on most flights, possibly when yawin
Read more…Dear all,
Thanks for reading this issue, I'm using PixHawk and Mission same version on both Tarot650 and Tarot680.
Actually impossible to retrieve on my Tarot650 DataFlash Log through General Menu - "Download DataFlash Logs via MavLink. While Still fin
Read more…Hi
I've just had a problem started occurring.
Occasionally halfway through a flight, one motor stops spinning and the ESC starts beeping.
Has anyone come across this before and know what it means.
It seems to only happen when I fly particularly aggressiv
Please see attached log and screenshot.
Flying mission with auto takeoff and waypoints. Plane perfectly executes take off and heads to first waypoint. Upon arrival at first waypoint plane pitches down until impact - even
Read more…Hello friends, I joined the group to share my knowledge and experience ... I discovered a problem updating my controller Naza high V1 to V2, the upgrade to "Naza-M Firmware v4.00 *" my controllers have stopped loading satellites, you can only see thr
Read more…Hello,I'm using my APM equipped DJI F450 to do some low altitude photo missions. I will be flying at 20m or so above ground. I have used the flight planner to create missions (survey grid) and have no problem with that. The question is, is it possibl
Read more…Hi,
I am interested to send some high-level control commands to pixhawk using MAVLink, indoors. So, I have a motion capture system setup which gives accurate XYZ and orientation. I would like to tell pixhawk this information in order to use it onboard
Read more…I'm searching for a port of the SiK firmware for the 3DR radios (HM-TRP) that will work together with Keil (or IAR) tools. I'm using Keil ARM tools for all my work and would really like to do some experiments with the HM-TRP modules using Keil 8051 t
Read more…Hi there!
I'm an avid hiker and am a lot in the mountains and far off the beaten path or parking lots. so what i want to build is a drone that is as small as possible but still has a gimbal for a gopro and at least 10min flight time. i hope you can he
Read more…