It's a brand new Pixhawk. (My fourth)
- The very latest Mission Planner build 1.3.31.1
- The latest Plane software 2015-08-11
After successful firmware update Mission Planner cannot connect at any speed.
I have tried with another computer, another versio
Read more…Hi,
trying to see what the feature Auto Analisis shows me after a flight I get this error messages:
and when I click OK, this:
Can somebody tell me what I'm doing wrong ??
(BTW I tried .log and also .bin files)
Thanks in advance! :)
Read more…Hi all.
Due to a mechanical motor problem I want to change my flat hexa to a quad temporarily.
I am running FW 3.1.2 on a pixhawk.
I removed two motors and ESCs. The frame stayed the same, but mechanical configuration now is as quadro.
Do I have to reloa
Read more…Hello
I just wanted to check if someone had the same problem after updating the mission planner, I am no longer able to geo ref images. I have tried to georef in three computers all running the latest version with no luck. I was only able to geo ref i
Read more…Hi all
I am building a new quadcopter, using PX4 and rotor, ESC from 3DR
I have a problem relating to PID tunning. I am using Mission Planner >>Config/Tuning>>Extended Param to send my values to my Drone
This is what I am doing:
First, I follow this guid
Read more…Hi
I've got a hexa with APM 2.5, power module and a minimOSD. This works fine for about a minute or so, then the overlay suddenly disappears. The blue led also stops blinking. If I try to reset the minimOSD I get one blink on the blue led and that's i
Read more…Hi
I build three quadcopters of size 360mm 500mm and 550mm using APM board and none of them holding altitude in loiter mode because of that I am unable to fly these quads in auto mode
I am attaching logs please help what is problem
Read more…Dear all,
In my flight test, I met one accident.
My hexa uses px4+apm flight controller.
during the accident, it flied in the loiter mode, and it flied backward, while I observed that the head was up and the tail was down, then I gave the RC command suc
Read more…Can someone help me understand why Kaspersky anti-virus identified and deleted a DLL within a recent Mission Planner update that is defined as a KeyLogger. I had to disable Kaspersky for the update to download; I was getting an update failed due to v
Read more…Hi all,
Would there be any issues with using double sided tape to fix my ESCs to the carbon fibre plate of my copter frame?
Think it's unlikely to be an issue but wanted to avoid learning the hard way.
Many thanks,
Read more…Running APM2.6 clone with ext gps and compass. 433mhz LR receiver and radio.
Never had this before.
Not sure If its a radio problem or a Board problem.
Fly my quad in Stabilize with great results. Haven't fine tuned Loiter yet , it tends to drift.
I hav
Read more…Hello,
Today I continued to setup my T450 with PixHawk and traditional hely.
I did three flight to tune the PI Rate Roll & Pitch but at the starting the fouth and checking the servo beavior I found may be a bug.
1. If I move the rudder stick all the cy
Read more…Hi,
i ran into a problem with the HIL-Simulation.
Normally, i am using Arduplane 3.2.2 on my Vehicle (Hardware is a HK Pilot Mega 2.5)
All newer Software-versions do not communicate with mission planner. I can connect, but i do not receive any data back
Read more…Hey guys,
I am trying to start up this plane I have with the Pixhawk installed on it. I am getting these sounds, and I don't know what they mean:
These sounds are not on the original list:
http://plane.ardupilot.com/wiki/comm
Read more…HelloIm searching for a pair of dongles that can run RTKLIB ie raw dataSuch as neo-m8t Lea-4t or neo-6tWith or without antennas dep on price and typeits for a diy project so im looking for reasonable prices./John from Sweden
Read more…Does anyone know what changes were made in the latest MP?
There isn't anything listed in the change log.
https://github.com/diydrones/MissionPlanner/blob/master/ChangeLog.txt
I see there are some changes to the accelerometer calibration. An additional s
Read more…I upgraded both my 2-axis and 3-axis gimbals to STorm32 v1.31 boards and they're working great, but after poring over the STorm32 documentation I'm wondering if I'm missing something with regard to connecting to the APM 2.6 FCs -- the docs make refer
Read more…I'm having a small problem with my Pixhawk controlled quad and am hoping someone can provide some insight. When in Loiter, forward flight is not straight forward but at an angle. Loiter does provide a stable hover in location but forward flight is th
Read more…OK, so I have some PID tuning to do to resolve an issue I have which is demonstrated in the video (link below). Its a twitch on the roll axis. Just not sure which PID settings to look at. The video is shot from both the air from a 3axis gimbal, where
Read more…Hello,
Is there a quick way to find out via the telemetry link what firmware version my Pixhawk is running ?
Read more…