Dear all,
I am very new for flying model "Skywalker" using Pixhawk. At first, when I turn the throtle up, the propellor can drive. But after I did following these;
- Loading firmware ( i plug in all cables into Pixhawk at this step ) http://planner.a
Read more…UBlox says that theit 7P device supports GLONASS. I purchased one from CSGShop. The trouble is that I can't figure out how to enable it. I'm using the latest u-center software v8.17 and trying to enable it in the GNSS configuration screen. Every
Read more…Hey,
Have been in aerial photography and geo-mapping scene for a long while, finally released a solution that any fellow aerial photographer and mapper would find super handy. ''Plug & Play'' solution as easy as it gets to setup and get shooting :) C
Hi,
In the old versions of Mission Planner we had the Start HIL Simulation, now I see the SITL Simulation in the Simulation Tab.
That option is working?
Why I don't find documentation about this method to launch the SITL? (I found just info about harde
Read more…I've been using mission planner with the default maps it's installed with. They were great, high resolution and recent imagery.
Today I tried a few other maps, and when I went back to google, I no longer get high resolution maps, or it's using a dif
Help. I recently purchased a CX-20 quadcopter which arrived with a faulty motor. I have changed the motor and all 4 now work but after unlocking they only accelerate up to fast idle and no more and the CX-20 cannot take off. I have calibrated all 4 E
Read more…Hi Guys ,
I've been using the APM 2.6 (No internal compass) with the NEO-M8N GPS+Compass via I2C. My compass directions are very inconsistent. I've done calibration several times but the direction is wrong.
When I point north -> Heading shows north -
Read more…My question basically is already written in the title:
Why are HDOP and VDOP in the MAVLINK message GPS_RAW_INT not unitless?
The definition is as follows:
| eph | uint16_t | GPS HDOP horizontal dilution of position in cm (m*100). If unknown, set to: UINT16_MAX |
Been saving up for a while. Its finally time to start ordering parts..The goal for this protect is to simply build an excessively powerful drone. I want lots of lift, i want thrust and speed. I wanna do stunts. I've always been interested in tri-copt
Read more…I have twe sky walker platforms both with different setups.the problem is in above 14 mph winds then spiral in while doing quite tight turns which they refuse to recover ..even the ardupilot cannot cope .. Should I move to the skyHunter instead Anyon
Read more…hi everyone
I need to ask that how much weight this quadcopter can carry.
http://dronefever.com/3DR-ArduCopter-Quad-C-Frame-Motors-Kit.html
Also if you have any other quadcopter suggestion which can carry some weight and its price is low too then please
hi everyone
I need to ask that how much weight this quadcopter can carry.
http://dronefever.com/3DR-ArduCopter-Quad-C-Frame-Motors-Kit.html
Also if you have any other quadcopter suggestion which can carry some weight and its price is low too then please
I have a Quanum Q-2D brushless gimbal on a quad with Pixhawk controller. This is the first time I have used a gimbal. I was unable to make the Pixhawk to Gimbal connection work using the Aux outputs of the Pixhawk connected to the pitch and roll inp
Read more…Hi,
on all the other FBL systems I have you set your collective travel (i.e. +/-10°-12°) and the cyclic for 7-8°. With 3.3 you do the collective, but I never found anything to adjust the cyclic in this or in older versions, therefore I used Dual Rate
Read more…I have the new apm pro mini from china. Had it working great until it stopped connecting. All I have is a solid green power and no action lights. Assuming ive bricked it, I've been everywhere on the net to see how to flash the bootloader etc. But all
Read more…I use an APM 2.5 running arducopter FW 3.1. It has flown for many months very well. After a crash which broke the micro usb port off the circuit board, one of the motors begins to spin only after the other three are at nearly 15%. I can take off, but
Read more…Hi all,
I'm trying to set up a plane with APM for my research. Everything seem to work find except for the fact that the plane always follows the planned path lines around 10 meters to the right (from the drone point of view). The path done is very st
Read more…I built avtail and have a kk2 flight controller. Angle of back legs is approximately 30 deg outwards. If I ascend at approximately 50% thrust, it rises facing the same direction. If I bump the thrust up to and beyond 60% and higher, it yaws ccw with
Read more…Hi guys,
I'm looking for help testing and writing "arduino" code for some cool LED lights on the bottom of quads. The idea is to have a small PCB that can take input from RC channels and interpret mavlink messages. Then you can place smart LED strips
Read more…I have run into an issue on the most recent mission planner update. It does not occur when rolling back the software to previous versions. When attempting to geotag photos from the DataFlash log from a pixhawk I get an error message and a really odd
Read more…