I am starting to build my good portable GCS and i want to instal a computer so run mission planner and display and record the fpv video and i was thinking in using this . It must be enouth and i can run it at 12v.
What do you think?
Read more…i was getting 12 sats on my 6H and swapped it for a N8M and what a difference, the N8M picks up 18-20 sats pretty much all the time, loiter is rock solid more than ever.....no problems at all was plug and play to my APM 2.7 with FW 3.1.5....did this
Read more…Catalin Alexandru Duru didn’t just set a new world record f
Read more…I know that the L1 controller has been out for about two years, but since I have had opportunity to use both L1 and crosstack, I still wonder if crosstrack did not actually provide better control of the desired flight path. What I truly liked about c
Read more…my Tarot 680 hexa crashed on a flyaway, i was descending then suddenly it started yawing right on its own at a constant rate....I tried RTL twice, no response...I tried to bring it back under STABILIZE...no control response, no throttle response...it
Read more…Hi
I want to command my fixed wing drone to fly a specific cross track error to a Nav leg.
Can I command a xtrack error?
Read more…Hello
I'm using a pixhawk with arducopter 3.2.1 firmware and a frsky taranis RC. I want that the RC failsafe that is built in the firmware to activate not immediately when the RC signal is lost but lets say 10 seconds after the RC connection loss.
Is t
Read more…Dear sirs,
I'd appreciate your help. My knowledge in electronics is not zero, but very limited.
I have an APM2.5, with Power Module, GPS, external compass and 3dr-like telemetry V1, on a plane, a big 2.2m span weasel-like flying wing, twin-motor, inten
Read more…I can not download the data log flash of missions, it is suggested to upgrade the AP, which I believe is the ARDUPILOT but can not find anywhere how to do this.
Already I tried to upgrade the Mission Planner to version 1.3.27 and yet problems persist.
Read more…Hello , I have problems with minimosd information. When I turn on the Pixhawk the minimosd information appears on my screen Fatshark , but without information, all can see is number zero.
I plugged the minimosd in Telemetry port 2 and Telemetry 9
Read more…Hi, this is my first thread on DIYDRONES. I have been flying drones for a bit over a year now, and bought a pixhawk a month ago. I converted my f550 clone (storm 6 drone) from the Naza to the pixhawk, and everything has been working quite well.
Excep
Read more…I will need accurate altitude estimates for video on a trip in July as they will be mission flights.
I think it was said Lidar does not work over water. Does sonar?
Read more…Hi All! Long time lurker but 1st time post, wanted to say hello and tell you all about Aerial Connect, it's a free drone directory website for users to post their profile for the general public to see.Hopefully you will generate work too. The website
Read more…Any drone rotors suitable for water propulsion?I think a regular drones motor would eventually burn out in water. Any rotors with slighlty different gearing or just strong enough not to burn out?
Read more…Can we make a GCS to capture some picture from OSD??
Read more…Although I have the maximum bank angle set to 45°, my plane would not achieve a bank angle over 30° when flying in FBWA or AUTOTUNE modes. In the air, it really appeared to be even less and the plane could not achieve a complete turn without switchi
Read more…To the developers for the future releases.
I would like to see the parameter in MissinPlanner that configure the time from when I press the safety switch to arm/disarm. Something like SFT_SW_DELAY in milliseconds, range 0-4000.
The reason I want this,
Read more…It is my pleasure to inform you that the faa has authorized the 3dr aero a 333 examption for flight in the United States. Mycompany M2 Flight Solutions has been apart of diy drones for a very long time and now has a 333 exampation from the faa to fly
Read more…Hi everybody,
I figured out that i get a very poor range while using openlrs (hawkeye Tx/Rx) with APM (mini arduflyer from rctimer). Indeed, I get a very good range while testing in the city (maybe 700m with a lot of batiments), but when I try again w
Read more…Hey there!
I left my Taranis at home when I left this morning, so I went and bought a DX6i with a satellite receiver to hook in to my Pixhawk.
When I attempt radio calibration, I get an error to the effect of: radio not connected or functioning.
I can s
Read more…