hi everyone!I come in search of some help on a quadcopter that I recently built. I am flying an auav-x2 pixhawk clone on a asymmetrical quadcopter configured as a v frame within parameters. I am flying 3.3 rc 3 and have tried auto tune several times
Read more…Hello guys.
Hello everybody.
I wonder if it is possible to mix the elevator with flap for landing.
My plane with pixhawk, when actuated the flap has a tendency to very nose up, and the pixhawk can not correct this trend quickly.
Someone suggest me some
See the link below. Currently considering all offers.
http://www.rcgroups.com/forums/showthread.php?t=2417727&highlight=X8
Read more…I have some strange behavior with my new build T960 on 3.3 RC4: Large oscillations on RCout but only on RCO5 and a bit less on RCO6 which suddenly stopped in this log. I am using Arris 5010 12 pole and BLHeli 13.2 with nearly stock settings (PWM high
Read more…Hi I've been building this H quad for a couple months now because of problems Withi wobbling so I figuered it was a bad esc and changed them all out. Since then I have had a number of unusual problems start effecting the quad. I messed around with th
Read more…I have Ubuntu-15-04 installed on my Laptop and i went to install Qgroundcontrol and discovered that when I followed instructions it went to install packages off Ubuntu website that it was coming up with Ubuntu-14-04 packages to install, do I need to
Read more…I purchased the ADNS 3080 and have connected it exactly as is shown in the setup guide. I have flashed the test hex file, but all I see for output is zeros, both in the terminal and with the python script.
When the terminal first opens the test progr
Read more…I wondering if to install MissionPlanner on Ubuntu-15-04, or instead Ubuntu-14-04 .
Below is the error I get when I try to install on Ubuntu-15-04. What is going on , i'm new to MissionPlanner.
The XXX in error message, am I suppose to enter apm64 i
Read more…I have told so many people about the 3DR crap, now after working on them for 1& 1/2 years full time day in and day out, thinking it'll pay off I'm finding I have smashed up way more than three times the amount of gear by using that Flight controller
Read more…Hello to all,
I apologize for bad english.
I have a few questions about log analysis and LOITER adjustments.
My quad is:
DIY quadcopter NightFox V2 (http://diydrones.com/forum/topics/diy-quadcopter-nightfox-v2) and setup is:
HP2814(3536)-810KV Multi-Roto
Read more…Hello,
I'd like to try a quadcopter with motors facing down. This setup could possibly provide better stability in the wind (hypothetical), I'm only guessing here. Since nothing will obstruct the prop wash, this could help. Now I'm not sure if I can u
Read more…Hi folks,
I had a quad Pixhawk, 3.2, which has had two "wobbles" in the air. Both occasions it looked like one motor shut down. On both occasions it turned back on and had enough height to recover (while falling I throttle at 100%)
Sadly the third occu
Read more…Hi,
I want to build something like this : https://www.youtube.com/watch?v=9DzqO1xBF7A
Others can do it: http://www.rcgroups.com/forums/showthread.php?t=1972686
Can we have it ?
Read more…I'm having a problem to upload a new firmware into my apm.
This is shown:
Does anyone help me?
I need to use the HIL firmware.
Read more…Hi,
In the Arducopter firmware there is a nice module implemented to protect one from GPS glitches AP_GPS_Glitch.h (not the EKF one), did anyone implement this on the Arduplane firmware? (the 16 bit version)
Hi guys,
Looked everywhere, and tried several methods to get the radio fail safe to work with the Taranis X9D.
I am of course trying to get the PWM of the throttle channel below the PWM in the radio fail safe box, so that when the radio or receiver fai
Read more…Has anyone had issues with the bearings in the MN2213 motors? I had a crash from low altitude. The props were beat up bu there appeared to be more damage than that. So I replaced the chewed up props and tried to take off, but the IRIS+ would not ho
Read more…In case this is helpful to someone, my build log:
http://marc.merlins.org/perso/rc/post_2015-04-23_FPV-with-Multiplex-Cularis_-v2.html
Fitting all the APM and FPV gear in there is kind of tight, but it's doable.
Specs:
Hi Everyone,
Very weird crash today. I have 12-15 flights all flawless before this incident. When it occurred I immediately thought I lost a servo - but upon inspection both servos were fine. Watching the video (below), I did not input the left roll
I’ve hit a wall when it comes to support from 3DRobotics. I placed an order for a Pixhawk + Airspeed + GPS + Radios a month ago. However when my order arrived a week or so later… NO RADIOS
I’ve sent several Service tickets ( via their web site ) and
Read more…