Hi All,
I have problem after updated Mission Planner to new version according to massage box that shown when I run the Mission Planner. I got stuck at "Got param RC10_MAX", the error massages are show below.
Please help me on this :)
Thank you very muc
Read more…Good morning. New to multi-rotor RC here. I spent literally the entire weekend reading and coming up with a design for my first build. I plan to build a Hex, practice and get good at it, then add/modify for photo and video. No sense in loading it
Read more…Buenas, desde que comencé tenía problemas con la brújula aunque no lo sabía.
Me he mareado pensando que eran los motores los que me creaba el problemas pero no es así.
Os cuento, el MagField me ronda los 280 aprox en reposo, pero cuando lo armo y le do
Read more…The good news: I am a senior computer design engineer with loads of had and SW experience and have been a LOS RCer for many years.
The bad news: I am new to FPV and UAVs.
I have been pouring over DIYDrones and 3DR sites for a few days. I am still a li
Read more…Hi
i am building uav for the first time and i dont know much types and brands of battery. please help me select a battery that can give 30 min of flight time with 55A of max currnt draw. this current draw is the total current consumption of my electro
Read more…My friend has a widows 7 laptop with a good working 1.2.33 mission planner. When I install 1.2.38 or 1.2.40 or the latest version 1.2.93 it runs the installation normally but the application does not run good.
mission planner does not show all the tek
Read more…I am building my first multicopter (a Hexacopter), and I am having problems with the speed being too high at lowest throttle level.
I am using MultiWii PRO Flight Controller, Turnigy 9X 9Ch Transmitter, and Turnigy Plush 30 amp Speed Controller.
I
Hello,
I am new to APM:Plane and appreciate any help I can get. I was able to maiden my flying wing today with success in manual mode (woohoo!). A few subtrim/ trims were made on my remote to keep it flying straight.
When i tried to switch to stabilize
Read more…I use APM2.6 with the 3DR power module. Today I updated MP to 1.2.95. Connect via USB or telemetry (doesn't matter).In the battery monitor (Initial Setup > Optional Hardware > Battery Monitor), I set the following:
Monitor: 4: Voltage and Current
Senso
Read more…Hi,
I almost finished assembly my F450 with APM 2.6 and have 2 question before i go to the filed.
1. Should i made a first flight with GPS or without it? GPS have a compass onboard. It will be mounted on stand pole so if i crash/flip it will be destro
Read more…Hi, I'm about to mount my APM 2.6 main module and was wondering if anyone had experience with placing their radio receiver in close proximity to the APM. My concern is whether doing so runs the risk of creating interference.
As you can see in the pho
Read more…Hello,
I am making a thesis about a system to auto land a quadcopter on a station based on a visual homing system.
I have already made some studies on the problem, and used Youtube footage to test some hypothesis. The problem is that visual homing is
Hello,
I am on my first APM-plane build. I'm having a weird issue where on boot of the APM, one of my servos is pushed 100% in one direction. This only happens if the signal wire is plugged into the APM.
Here's a video: https://www.youtube.com/watch?v=
Read more…So I've read around that there's no failsafe on the stock Turnigy 9xV2 system, which seems pretty damn stupid to me.
However, I've noticed that if you actually trim the throttle up, you could set it (through calibration in Arducopter) that your min th
Read more…
OK, so I read the line which states: "The presence of a drone at a crime scene for journalistic purposes is in violation of FAA regulations
Read more…Can some one help me. I have been throughout the forum and can't seem to find a direct detailed answer to my question.
I know there is an article with an option to connect a GPS module via "bypass" through the APM2 to connect to the u-center, however,
Read more…Hi everyone, this is my first post on here and i would like to thank everyone for all the hard work and long hours helping others.
So i am running mission planner 1.2.94 and using a steadidrone quad with 12" props, extended landing gear, gopro, no gim
Read more…Hi Guys,
I came across Rolfs great project where he is converting MAVLink to FrySkys Smart Port protocol with an offboard processor and sending to the FrySky X8R which then beams the telemetry back to Taranis transmitter so you can view data on Transm
Read more…Does anyone know which parameter group I can find airspeed to log (passively). I have looked in CTUN and NTUN but neither appear to have this listed. Any hints and tips here...?
Read more…Hi All
I think my telemetry port may be damaged.
I tried to set up a minim osd but i failed to understand the wiring correctly.
this worked ok when powered from the usb link
however when i connected the main lipo battery (camera and Tx 12v fr
Read more…