When i go over 50% of the throttle, the motor seems to spin @ 100% gradually but quickly and yaw to the right. Hear the sound of motors in the video. What can i do now?
Thanks
Video: http://youtu.be/qeatK4JFG6Y
Read more…
I have try the latest version of APM Planner and i have notice that with this particular version in th HIL the APM did not take the Heading that Xplane send .
I will a roll back of version .88 and the HIL mode work correctly .
Read more…Just an idea - nowadays 3G modems cost nearly nothing with their free plans for few months. So I guess it has main chip which can accept AT-Commands like:
AT
OK
AT+CMGF=1
OK
AT+CMGW="+85291234567"
> A simple demo of SMS text messaging.
+CMGW: 1
OK
AT+CMSS=1
+C
Today I was flying my Quad and went to take off, pushed the throttle up just a little to make the props spin and then after more input the quad was not responding... Went to repeat the process but the second time it didnt even moved the props :( . To
Read more…Hi all,
After spending more than 2 days trying to get my EM406A work with my ArduIMU (v1) in binary a finally gave up.
I reset it all as an NMEA gps at 38400 baud and made sure I had a working GPS that got a fix using a terminal prograjm.
I ran the IMU
Read more…i am building my first QuadCopter and i am having a hard time picking the motor to use either the Turnigy 4240 Brushless Motor 1300kv or the Turnigy 4250 Brushless Motor 1000kv i know both have a max thrust of about 2400g. Can any one tell me wish wo
Read more…I am getting following error use AC2 v2.6.37+ i have used the latest version any body else having the problem with mission planer version 1.0.91
Some of the major players suffered an xbee bricking event:
http://www.bbc.co.uk/news/science-environment-15698439
At least we're not alone :-)
Read more…Hello, i am in need of a hexacopter that can do some heavy lifting and have a very long range of flight using ardupilot or waypoint. im new to this and do not wish to wasts my time learning for too long and getting noweere. I would like a hexacopter
Read more…I've been having a problem here and there and not able to pin it down. I've included a log of the last flight. What is happening is the horizon in MP shows that I'm not level and I have to use more stick to the opposite direction to keep it level. It
Read more…I'm assemble on my glider APM+OilPan+Xbee+Voltage and curren sensor+magnetometer with arduplane 2.24 and ArdupilotMegaPlanner to GCS, everything begins to work well but the air speed sensor is maintained at 0 with peaks 2.5m / s (according to the MPA
Read more…all of a sudden my xbee wont connect in the mission planner it was working fine yesterday .can someone steer me in the right direction i am sure i have the right com port and baud rate already how do i figure out the problem ??
Read more…I have connected the APM and have the CLI switch to On. I'm testing the control surface deflections and noticed that they are noticeably delayed compared to flying a plane w/o autopilot. I assume this is normal since the signals have to get processed
Read more…Has anyone else seen this? http://www.e-volo.com/Home.html
It was in the Elektor newsletter. The Multicopter has 16 motors which to be frank look like larger RC brushless motors.
I want one!
Read more…Yestarday i flew my APM in a skywalker for the first time and had a couple of questions /concerns first i flew in Manual mode and everything was fine when i switched to stabilize it would stay in the air but shake allot i know that means the gai
I have built two Telemetry sensor stations base on Arduino Pro Mini board that gives me one RPM, one Temp, all gps data, and voltage and current on the transmitter display.
I also added total current used (displayed in RPM 2 field on the transmitter).
Read more…Yestarday i flew my APM in a skywalker for the first time and had a couple of questions /concerns first i flew in Manual mode and everything was fine when i switched to stabilize it would stay in the air but shake allot i know that means the gai
Read more…Title is self explanatory :)
How would you connect a switch on an RC transmitter to control the relay on the APM board???
How much code needs to be changed?
Thanks :)
G
Read more…I use Arduino to upload program to ArduPilot. Could soemone advise me how to download the program from ArduPilot? I want to know the existing setting of my ArduPilot for PID adjustment . Thanks.
Read more…I noticed that Gary just deleted his blog entitled, "20 million pounds for pocket sized UAS".
Sure hope that he was not forced to do that. I can understand that DIYDrones promotes non-military use of UAVs, but that shouldn't mean we need to ban discus
Read more…