Hey guys!I am building the arducopter with RC control and also have to figure out how to get wireless communication working so I can send mission commands via laptop and then eventually android. I know I can put the Xbee shield on it but from what I
Read more…G'day all,
I'm still doing my research on building my first UAV and so far the Skywalker looks like a pretty good candidate but I'll be operating in high wind areas (like the tops of hills) in unrestricted airspace. I was wondering if anyone has play
Read more…Hello,
I have some voltage output probleme on the IMU pin 0 (As indicated in the attached picture)
The output voltage is 0.1 V!!!
Any suggestion?
Thank you.
Read more…Hi guys,
First, i'm from France, so apologize me about my english ;)
I ordered the APM 4 days ago, everythings works great but from day to another one, the APM doesn't want to boot (no led ABC blinkings..) so i made somes tests with arduino IDE and t
Read more…I have gone through setup and set my frame to hexa+When I arm the motors only 4 motors spin. The front and back motors do not spin. Also, when I tilt the copter I was expecting the motors to attempt to level the copter which they did not do. Help ple
Read more…Hi ,
Atmel has recently released the new (blue) Xmega A1 Xplained board (29 USD) and plug on sensors ATAVRSBIN1 (Inertial One, 54 USD) and ATAVRSBPR1 (Pressure One, 24 USD). A few days ago ATAVRSBIN2 (Inertial Two, 54 USD) expanded the line of senso
Read more…I am planning to add flaps to the plane and wondering if I should just add it as an extra channel on the transmitter or should I incorporate it into the APM 2.1 code.
Would it effect the "stabilized", "fly by wire" etc mode flying, or APM would comp
Read more…I have nearly finished convert my quad to a hexa. I want to fly in + mode, could you let me know which arm to point forward. The wiki only shows x mode drawings at the moment. Great job acm2 team
Read more…Hi Folks, Im new to these forums but have been lurking for a year,First Grats on AC2 Beta, the Mission Planner is excellent and the CLI is very comprehensive. I think you guys are poised to dominate with this combo :)
I Have built a Custom Coax Octo
Read more…i have battery (http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=6306) 11.4V,ESC (http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=14870) and motor (http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduc
Read more…I am trying to compile APM 2.1 with Arduino 0020 and I am getting the following error message: "C:\Users\Kevin\Documents\Arduino\libraries\APM_RC\APM_RC.cpp:27:3: error: #error Please check the Tools/Board menu to ensure you have selected Arduino Me
Read more…I can connect to the HK CGS fine, but I can not connect to the PID_Config or Planner MavLink via XBee.
This is the ERROR message
I've been looking to buy one and I'm not sure which one would be the easiest for a beginner.
Thanks,
Nick
Read more…hi. i uploaded the code via mp, tried to test it via mp and into the same issue as in
http://diydrones.com/forum/topics/arducopter2-trouble-connecting?id=705844%3ATopic%3A362863&page=1
but i have the gps connected properly... then tested everything
Read more…I have a clicking noise from one of my motors (or possibly several motors, I can't tell). Is this normal? Is it a faulty motor or ESC?Actually one of my motors failed the other day, but I don't know if it's related:https://www.youtube.com/watch?v=pd2H
Read more…Hi guys, have tried using NG code and the ac2 code, setup goes fine, but can't get it to arm! once power is connected esc's do their startup beeps and then front and right esc's keep beeping at approx 2 times a second and i can't get it to arm, green
Read more…I've been running NG RC2 in X configuration and noticed in the docs for Arducopter 2 Beta 1 a difference between these two pages:AC2_Frame_Assembly - mount the APM pointing forward towards the left armAC2_Radio - mount the APM pointing between the 2
Read more…Hello,
Today I received my ArduIMU V2+ (http://store.diydrones.com/ArduIMU_V2_Flat_p/kt-arduimu-20.htm) and my FTDI Cable 3.3v (http://store.diydrones.com/FTDI_Cable_3_3V_p/ttl-232r-3v3.htm).
I began following the Getting Started Guide and get this e
Read more…I have connected and uploaded the new code via mission planner. I have gone through the setup with the CLI and MP. When I slide the switch forward to the fly position and try to connect to the mission plannner it never connects even with gps lock? I'
Read more…Is there a way to download the APM manual for those wanting work offline?
Read more…