Xbee pro 868 compatibility
Hi,
Could anybody confirm me that the APM is compatible with the XbeePro-868 (as I'm european) ?
many thanks !
Read more…
0 Replies
All Discussions (17281)
Sort by
Set RTL / Home Point by Button on Transmitter?
Hello,
I use the Ardupilot mega for FPV flight and the best function for me is RTL. So here is my question:
Is it possible to set the RTL Position in Flight?
Reason:
On different flight places the RTL position ist not the best position to circle. Bette
Read more…Arducopter- view data from sensors
I have an Arducopter but I don't have Xbee.How can I view the data from the motors,GPS,sensors.Is this data saved somewhere?
thank you
Read more…Can't test IMU
Hi, I'm hoping someone can help me.
I added the code per http://code.google.com/p/ardupilot/wiki/Test
then compiled and uploaded the code
#define DEBUG_SUBSYSTEM 6
I go to the console and type "test". I get many options when I type "help", but not IMU.
Read more…Getting rolling on an old Oilpan
Hello All!
I was very excited to get my Adupilotmega... almost a year ago! But circumstances did not leave me with a chance to get to playing with it.
Today I popped it out to get rolling and do some playing. My first order of business was to check eve
Read more…sending UDB telemetry data over video link + decoding with a video grabber card + showing a virtual cockpit in 3D etc
Hi,
I did a small project initially for FPV, which is basically a virtual cockpit in 3D, showing data collected from an onboard (remzibi) osd.
A video will better describe what it does :
The originality is that the telemetry
Read more…Pulsing motors
I have a pre-soldered kit running RC1.When I switch it on all pre-flight checks are fine. When I then increase the throttle and leave it, first the clockwise motors speed up and then return to the rpm I set, then the counter clockwise motors do the s
Read more…Turnigy 9x switch mode setup for ArduPilot Mega
Hi,
I found this useful decryption of how to configure switched on Turnigy 9x to change modes.
http://rcav.posterous.com/programming-an-ardupilot-mode-switch-for-turn
Regards
Marek
Read more…ArduMega
Hello!
I have a big problem
I connect my boards to USB port.
Rx/Tx together blink 3 times and nothing ... everything power down except the blue Led from ArduMega and the red, yellow, blue on the red board.
It is very strange because I put code well befo
Read more…Fuzzy Quadcopter
Hi!!How are you??Last year, i design a stabilization system for a 3d helicopter, using neuro-fuzzy systems, it worked great!!!now, im designing a quadcopter, just like everyone else, hehehe, but with the same difference, its going to use fuzzy logic
Read more…XY Gyro not working
I have checked and rechecked everything I can think of. When performing IMU test using the terminal it goes to:
Init Gyro**************************************
Yes my solder joints are good, I have carefully re soldered everything, inspected with a m
Read more…ACM Code question
From the way the motor test video looks we wont have to worry about burning out our APM any more by having the motor outs plugged in without battery? Is that correct? I remember it used to cause brown outs that would kill the APM if you plugged the U
Read more…Throttle in Manual mode (not working) and stabilize (working)
Hello,
I have an APM 1.0 board that gets power from an ESC, LIPO battery 11.1. I have connected 3 servos, xBee, Mediatek GPS and the RX to the board. When I'm in manual mode I don't have any control over the throttle. When I mode the stick to 25%, 50
Any I2C Pins on APM ?
Is Analog Pin 4 (Port PC4) for I2C SDA?
Analog Pin 5 (Port PC5) for I2C SCL ?
Lastly is Port PD1 for I2C SDA?
and Port PD0 for I2C SCL ?
Read more…any altitude data from the Telemetry port ?
ok,
I'm not using Xbees for telemetry,
but i'm thinking of transmitting the altitude data to ground using my own transmitter and microprocessor.
is the telemetry port spitting out altitude data ?
at what form ? or what qualifiers can i use to 'catch' t
Read more…APM 2.1 - No flight data transmission (Unusual LED behavior/wrong setup?)
I have previously had success flight testing my Skywalker EPO UAV with ArduPilotMega. Both stabilize and fly by wire A functions worked flawlessly, but due to safety issues I wanted to embed a bidirectional radiolink before attempting autonomous flig
Read more…Mini-size bluetooth joystick remote for Windows or mobile phones
Here is a really small easy to use mini-size bluetooth joystick remote for Windows and some mobile phones, under $20 on Ebay. Can be set for use as a mouse, for Powerpoint, or your own custom programmed keys.
Here is the link the the website:
Read more…Current Monitoring Issue
Is anyone else having trouble with the current sensor? In the CLI, my current draw appears to be correct but the voltage always reads around 2. Is there a multiplier I need to set somewhere?eg: V:2.6917, A: 0.0.0023, mAh:0.3851I'm running stock 2.1 a
Read more…Newb - Can you look at this mission?
Hi Guys,
Just a quick question. I specifically want to look into a drone to fly this flight pattern (see at end) with a gopro camera, and then be able to post the video on youtube.
I would pretty much have LOS the whole time,
I would prefer to have a si
