As a total noob, I'm sure it's staring me right in the face lol! I'm setting up an X8 flying wing and even after selecting elevron mixing the elevator and ailerons still operate separately. The instructions for the mission planner say to click on "
Read more…I need to purchase a ground station computer to run Mission Planner.Looking for suggestions for a screen that is viewable in full sunlight. Most that I have seen are using a glossy screen that causes too much reflection. I have seen a couple matte sc
Read more…Hi all
Why can't we have CH6 PID tuning on Arduplane?? Is there a good arument for not implementing this in the Arduplane software ? Would be much easier to tune the pid's.
Tommy
Norway
Read more…Odd behavior from my HIL experiences the past two days.
I have done HIL many times before but am experiencing problems now.
Problem 1: APM does not arm until xplane connects.
Problem 2: Once it IS all connected, heading of aircraft in MP is off by about
Read more…I'm running the latest APM code in a Zephyr II and it flies well in Stabilized and all Auto modes, tracking waypoints and altitudes great. In FBW-A however I can't get more than about 10° bank and very shallow climbs and descents. Had anyone else exp
Read more…Has anyone here used the px4 board with futaba sbus system yet, would love to hear from anyone as im stuck scratching my head.
regards
Read more…Why doesn't Mission Planner for Arduplane have a selection to assign channel 7 to RTL like it does for and Arducopter? I love the security of being able to select RTL regardless of what flight mode I'm in. It has saved me more than once with my Arduc
Read more…Hello all,
After so much success with the APM I have decided to try a px4 :) due top the much increased processor capability however I am now stuck, all firmware is loaded and works in mission planner but I cant find where to connect the receiver to t
Read more…Hi the enable led comand in mission planner is missing in arduplane, it was there in arducopter.
is there a work around?
cheers
Read more…Hello all,
looking at the wiki I can only see info on the px4 in the arducopter manual not in arduplane is firmware available for the arduplane?
regards
Read more…
Hey guys,
My EPP FPV has this bad habit of pitching down when the throttle is increased to maximum in both manual and auto mode (CG is perfect when I'm flying in manual mode, no trims). It may be indicative of bad thrustline or flexing of the entire t
Read more…I am not sure where to enable this parameter FENCE_CHANNEL
I would like to set up Geo-Fencing however reading through the manual give no clue where to set this. I can see the other parameters OK however this one is not there in Mission Planner that I
Read more…Can anyone tell me where the release notes for arduplane 2.71 are? would like to know what has been changed.
thanks all
Read more…
To all you Pitot/Static tube users - beware. Three out of three of the 3DR pitot/static probes I purchased recently have had air leaks where the internal tube joins to the machined aluminium tip. In one instance this resulted in a 20% under-reading o
Read more…Im doing tuning on a hobbyking epp fpv with arduplane 2.68 and the left bank in fbw a is severely limited. Planes flies normally on manual and stabilize but it just doesnt go left. It goes perfectly straight and right but no left bank. Pids are stock
Read more…Hi guys
I'm having a bit of a problem with the throttle during auto/RTL mode. Although the max rc throttle in standard parameters is set to 100, the throttle never goes to full. No problem in manual mode though. The problem arose after I uploaded the
Read more…I have 2.7 on a 2.5 APM - the problem is that when I select RTL or AUTO the throttle cuts out.
I have read previous posts on this however on reviewing the logs the altitude is correct, the airspeed is working and is correct. Stabilise works and a hav
Read more…hi,
im trying to add a mount configure DO command to retract my mount, but I cant write the waypoints with the command in line. it says its not supported...
video of my problem:
Read more…
Hi group
If I set THR_FAILSAFE to 1 and switch off my transmitter, then the APM goes to CIRCLE mode after 1.5 s and to RTL mode after 20s. It does that if short and long FS are enabled. But it also does that if they are both disabled.
Perhaps more worr
Read more…Group:
Today I did some flight and photo mission tests. Overall they went OK, but the plane is not tracking the way points properly. One issue I am sure that is correctable is the fact that it tends to meander to them and not go straight from one to
Read more…