Hello all,
A definite fault in the code, when entering auto mode via mission reset when the plane is above your desired altitude the plane will go to high throttle and nose down and will not pull out unless you go back to manual, however if you missio
Read more…I noticed someone else posted this earlier there is no option to calibrate level in the mission planner screen, looks like this has to be done direct from the CLI, does this mean this will not be available via the normal way on mission planner? or wa
Read more…What command is used to level in CLI I cant find any command under test?
regards
Read more…
Greetings esteemed UAV-ers...
I'm running an APM2.5 board in a ParkZone Radian (3 controls - throttle/rudder/elevator).
My initial manual flights were successful, including running in Stabilize and Loiter Modes (using my Spektrum DX7s 3-position flap t
Read more…hi i tried to level my apm and when i opened the level fonction it show (calibrate accelerometer)
the level fonction have vanished i also tried to find the manual-level in the advance parameter list and did not find it
thanks
Read more…hi everybody its me again
i did some bench test with different flight mode in fby A i dont have rudder controll is that normal
thanks
Read more…hi i have tried to set the throttel fail safe when i shut off the transmitter of the baud rate stay the same 1121
there is no drop in the baud rate number
thanks
Read more…Hi,
I will use a catapult launcher to throw a heavier X8 wing and I want to use the auto take-off APM 2.5 function. I did read that it needs 3m/s before engaging throttle. So here are my 2 questions:
1) When changing to auto, does the throttle stick n
Read more…I would really appreciate some help as my Skywalker is losing altitude when RTL is commanded. While flying in manual mode I did notice I needed to add up trim to the elevator and I will correct this before the next flight, could this be why RTL behav
Read more…After flying two (arduous) 20km FPV flights, I was thinking it would be fantastic to have a mode that would keep the plane heading, altitude and speed. FBW & Stabilize holds the plane level, but it drifts. Auto requires I pre-load waypoints.
This woul
Read more…Hi guys,
I have a question on tuning for level flight in auto mode. When the plane throttles back due to increased headwind during a leg, the plane maintains a steady left bank of about 3-5 degrees. When it needs more throttle to maintain the target a
Read more…Guys I need your help, APM 2.5 is new for me it´s the first time. When I connect my usb cable to my bixler on the field, the red plane on the mission planner is opposite (almost everytime) to the true north.
What I did to solve the problem:
1- Check o
Read more…I can't get to work the radio calibration.
In the terminal i get this error as you can see in the image and the video shows.
Can anyone help?
I have been having trouble getting my TetraCam time stamp to sync with the APM log following the instructions found at http://diydrones.com/profiles/blog/show?id=705844%3ABlogPost%3A1054809&page=5#comments I have read in an older forum that the APM
Read more…2013-06-24%2014-11-32%20%281%29.tlog
Hi Guys,
I have Arduplane 2.73 on a plane I'm working on and it flies a mission quite well right until it reaches loiter altitude in home. Upon reaching home, it does a descending turn as expected until it reaches d
Read more…Hi guys,
I'm currently running a Super Sky Surfer with this setup
Arduplane 2.73
4 HS-82MG for ailerons and flaps
1 HS-225MG Elevator
1 HS-85MG Rudder
CC 10A bec to power ardupilot, receiver and servos
My flaps are currently connected straight to the receiv
Read more…Hello! I am having a problem where my aircraft will reduce throttle to zero when I switch on Auto or Loiter Mode.
Here are a few things to note:
Hi Guys,
I'm not sure if it's a new feature with the latest arduplane update, but the fields to change Nav Roll and Cross Track is unavailable in the PIDS page on the mission planner. Is this normal? I downgraded to 2.70 for the meantime since 2.72 is
Read more…Hello all,
In previous firmware there was a option to pick GPS or Barometer or both for altitude control I have noticed in the new firmware this has now been removed, does anyone know how altitude is now controlled in the code GPS, BAROMETER or both?
Read more…
Read more…Dear Customer,
You are receiving this notice because our records indicate that you purchased an airspeed sensor from 3D Robotics. Our ongoing product testing has turned up a rarely occurring issue that can cause poor performance of the airspeed senso
