In ultralight aircraft ballistic recovery systems are becoming more popular and some aircraft are sold with them as standard equipment. I've looked but haven't found any for our size of UAVs. Is anyone aware of a company that makes them? Perhaps thos
Read more…My failsafe is setup and goes into failsafe mode fine, throttle down
When I put my turn off my Tx my failsafe is setup and goes below Pwm just fine
My question is my switches also go back to a preset position throwing my Flight Mode into STABILIZE (or
Read more…Hi, I'm new here. I hope you can help me.
I do not quite understand the instructions.Perhaps it is also because my english is very bad ...
Next week I should get my APM 2.6 for one of my Tricopters.
I wonder at the moment, if I have to consider the supp
is is possible to control my gimbal over telemetry. I dont have spare channels on my transmitter.
Thanks
Damo
Read more…Hello,
In continuation of selecting the best motor for my X8 (Octo coaxial) build for video/photography (see post here : http://www.diydrones.com/group/arducopterusergroup/forum/topics/tiger-motors-propellers-combinations-for-an-heavy-lift-octocopter)
Read more…I am getting a pretty darn bad jitter, looks like a signal pulse in my Gimbal making it almost better not to use it.
It was my last flight, Im not sure if its actually getting an actual signal thats telling it to do that or not but I know its not the
Read more…I attached the telem log.. Was doing a gimbal test this morning and did my usual check list had 12 sats everything checked nominal. Launched the hex and went to apprx 20 feet hit the loiter switch.. instantly it went into it then in another 2 seconds
Read more…Can I arm, take off and start mission from MP.
I can now do a mission fine from the controller, but I was wondering if I can arm the craft and start/end the mission <take off, WP, land> from MP?
Read more…Did a full automated flight, take off waypoints and then land
It went pretty well but the landing did a little hop after touchdown.
At the end it went to the RTL position, came down smooth to about 3 feet from the ground, then it oddly did a little pau
Read more…The first flight went pretty well, tested stabilize, moved forward, switched to RTL and it came back, flew backwards to get home, I assume thats normal, was not sure if it would turn and face me or not.
The only thing I found to me, for my preference
Read more…It looks like disarm time after landing is about 15 seconds. Is there a way to change that to 5 seconds?
I looked in the standard parms but did not see the setting.
Thanks, Ed,
Read more…So first good news.
Direct replacement of my NAZA-M to an AMP 2.6 on my Flamewheel f550 hovers in the living room.
But
When I put stick forward it went back and back forward.
So I reversed the Servo and it seems fine.
But Im a little worried that when I
Read more…Hey All,
I have a FPV-Quad with DJI-OPTA 30amp ESC's and 3DR motors. This is all controlled with a APM2.6 Unit, with GPS and Telemetry. I am controling with a er9X controller with the added board for easy USB updating and programming.
Issue:
On poweri
Read more…Picture shows MP found it on COM 6, Driver loaded.
Does not show is lights green on PC module, on Air module one light green and one yellow.
Tried to load settings, Upload Firmware Local and nothing works :(
I am having trouble switching between flight modes. Everything was working well yesterday , no problem switching between 6 different flight modes.
Mission planner popped up with an update when I started it this morning and I chose to update. No idea i
Read more…I am using APM 2.6 on Quadrotor. I had couple of flights with 4 cell lipo batteries. Today when I connected 4 cell battery to battery monitor, it burned off with smoke. I removed battery monitor and tried to arm APM but it did not arm. Now I am tryin
Read more…I am currently using the Spektrum DX7s and it has worked well for me using the APM 2.5 on my hexacopter. All though, after setting up the transmitter for six modes for Arducopter and the pitch/tilt control on my camera, I am maxed on my channels. N
Read more…It seems I have to cut my red and black wire and somehow connect it to the PWM Outputs
Its dissapoinging it wont work off the AMP 2.5 to say the least
Is this the PWM? Im not even sure what it is
http://store.3drobotics.com/products/apm-power-module-wi
Read more…Getting an error trying to connect to AMP 2.6
USB Plugged in
Dropdown on Com 5 shows
Ardu Mega 2560
So I assume it sees it via USB
Select Connect and it fails
So I've got 3 3DR Quads that I would like to start using for aerial mapping and a variety of other applications which require cameras other than the GoPro. Has anyone figured a way to mount a dual axis camera mount centered beneath the quad? I would
Read more…