I am having issue with my Ailerons and rudder not moving in the correct position.
I have followed this tutorial and a thread on here, however I still can not get my rudder or Ailerons to go in the correct position.
I am using a Royal Pro 7 Transmitter
Read more…Hi, I'm new to pixhawk multirotors (coming from Naze32 / 250-class racers). I'm working on building a Tarot-690 Hex for an Aeiral Photography platform using PX4. Obviously I have a bunch of questions, and someone on reddit pointed me to DIYDrones as
Read more…Hello,
Have problem with shaking servos.
Configuration is follow:
Pixhawk with arduplane
Servos - CYS-S0307 3.7g Analog Servo http://www.cysmodel.hk/en/ProductView.asp?SortID=45&ID=190
Radio: Flysky RC 2.4ghz Radio System FS-TH9X 9ch Transmitter Receiver
W
Read more…Hi all,
I'm amassing a library of video tutorials for would-be UAS programmers. My foundation is with the PX4 stack on the Pixhawk. What flight stack do you guys vote to be more in demand -- Ardupilot or PX4?
Please contact me if you're interested in d
Read more…I would like to connect a 433MHz module directly to the telemetry port of the pixhawk and a companion computer (raspberry) to another port of the pixhawk.
However, i would like to have a UDP connection from the ground station to the companion computer
Read more…I have set up 3 quads now but for some reason after installing a new pixhawk on this quad [ that flew fine with another pixhawk ] I cannot get rid of this 'bouncy' quad. I have tried auto tune, high pids, low pids and nothing seems to fix it. Here's
Read more…Hi everyone,
I would like to power my Pixhawk from 6s lipolly. I'm gona be using attopilot 180A, I have to add some BEC 5V. I choose Turnigy.
I drew a scheme and I would like to ask you: Is it correct. It can be work?
Read more…
I am a complete beginner at this multi-rotor hobby in general, and PixHawk in particular.
I have two new frames I wish to build, a Quad (FCP-HL) and a Hex (Vulcan Multiframe 900) and will be using T-Motors on both. I already have 6 off JETI HiCopter
Read more…I'm not sure why, but I do not have full throttle when connected to my Pixhawk. The reason I say this is that when I am at half throttle all motors spinning (Y6, newest version firmware loaded), but when I place the flight mode switch to RTL my motor
Read more…Hello
Need a help. Problem is follow: when I connecting my four servos and esc with motor directly to receiver, everything work. Than I try to re-connect, servos go to outputs 1,2,4 and esc with motor to 3. Receiver connects to Pixhawk through ppm enc
Read more…Hi Guys I have a 3DR Pixhawk and i want to install into my DJI S800 frame, the first thing is i need a power module that supports 6 cell i found this one.http://www.ebay.com/itm/301131264504?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
Read more…
Took my QAV540G for a flight today, only its second. And got a PM Fail. I've attached a file for you to view. Can someone explain what it is and how do I fix it. It set off the failsafe. Look forward to your reply.
Read more…Hi everybody.
I'm desperate and can someone please help. I'm trying to set the Failsafe on my Pixhawk so that when my Taranis loses the connection or gets turned off the RTL jumps in. I'm using a EZUHF RX. I've done just about everything I can think o
Read more…Is it possible to tell the pixhawk the offset of your GPS mount location from the controller or CG? I would like to mount the GPS in the tail of my copter far away from the gimbal, ESC's and other sources of interference. However this means with 500m
Read more…Is anyone running this GPS on their Pixhawk BeStar BN-880 Ublox NEO-M8N GPS module with HMC5883L ( Compass ) and where do you get them from? I see the GPS that comes with the Pixhawk seems a little old now.
Read more…Hello,
I was hoping someone could help me out with some PID values to use as a starting point to use with pixhawk. A friend has replaced his Wookong with a pixhawk in his y6. He has had success with fixed wings and quads with pixhawk but his y6 build
Read more…Hello everyone:
Wondering if anybody have used EMAX 4IN1 ESC (25x4) ESC with Pixhawk?
This is the official page for this ESC:
http://www.emaxmodel.com/views.asp?hw_id=1305
Read more…Hello,
Have my Pixhawk with ArduPlane and gps neo-n8m. After every start Pixhawk logs his trajectory to card in .bin format. try something to change in mission planner but it still logs in bin. Can I somehow configure Pixhawk save also u-blox format (
Read more…Is there consensus on the best ground station platform? I'm a Mac user (and have downloaded APM2 at home) but hear lots that Windows using Mission Planner is superior.
I need a new laptop for 'work' - should I go windows or stick to Mac?
Read more…