About

Gender

Male


Location

Wimberley, TX


Please tell us a bit about your UAV interest

Just getting started in quadcopters


Hometown:

Wimberley, TX


Activity Feed

Bo Wingo replied to crystal garris's discussion lets get organized! in techpod dev group
"USA"
May 14, 2014
Bo Wingo replied to Mike Bell's discussion 3DR Y6 wont lift off in ArduCopter User Group
"Check your propeller orientation. Is the embossed writing denoting the propeller size and direction facing the sky? All six propellers?"
May 11, 2014
Bo Wingo replied to crystal garris's discussion Skype meeting saturday - now sunday in techpod dev group
"Was waiting to see if I was going to be available before replying. Doesn't look like I'm going to be able to make it."
May 11, 2014
Bo Wingo replied to Thomas's discussion [SOLVED] First Flight - My F450 can't lift of the ground in ArduCopter User Group
"Wow. Good catch, Gary. I never knew DJI made things so complicated. ;)"
Mar 2, 2014
Bo Wingo replied to Thomas's discussion [SOLVED] First Flight - My F450 can't lift of the ground in ArduCopter User Group
"Your second photo is the correct orientation with the lettering on the top side of the propeller."
Mar 2, 2014
Bo Wingo replied to Sean Headrick's discussion Need to delay at landing/before takeoff for water sensor measurements in ArduCopter User Group
"Great Dog:)

Thanks."
Feb 15, 2014
Bo Wingo replied to Sean Headrick's discussion Need to delay at landing/before takeoff for water sensor measurements in ArduCopter User Group
"I haven't used it, but maybe give CONDITION_DELAY a try?"
Feb 15, 2014
Bo Wingo commented on Hugues's blog post How-to guide: Pixhawk with 6S batteries (> 4S)
"You're welcome."
Feb 12, 2014
Bo Wingo replied to Bo Wingo's discussion Collection of Graphics? in ArduCopter User Group
"In case anybody's curious, I re-discovered the page that I was looking for.  It's on the Developer wiki and is titled "Graphics Resource Page"."
Feb 11, 2014
Bo Wingo commented on Hugues's blog post How-to guide: Pixhawk with 6S batteries (> 4S)
"@Hugues,
Have you proven this 150 A scenario by measuring the current with an ammeter and comparing it to what the Pixhawk reports?
I ask because I do not believe that the voltage division is as straightforward as it seems.  If you look at this sche…"
Feb 11, 2014
Bo Wingo posted a discussion in ArduCopter User Group
Is there a page that offers a collection of 3DRobotics and general DIYDrones graphics?  My memory is trying to convince me that there was a page on the wiki that just had a collection of images of all the common components used in an aircraft build…
Feb 6, 2014
Bo Wingo replied to Hugues's discussion what frsky receiver for pixhawk? in ArduCopter User Group
"Doesn't the Pixhawk support S.Bus as well as PPM?  In that case, you could just use an X8R receiver.
If you really do need PPM, how about an X8R with a FrSky SBUS to CPPM Converter?"
Jan 22, 2014
Bo Wingo left a comment on ArduCopter User Group
"Good deal.  Just out of curiosity, what voltage did you measure?"
Jan 8, 2014
Bo Wingo left a comment on ArduCopter User Group
"@Dennis,
This regulator is being used to take the 5V board input and regulate it down to 3.3V.  When a regulator fails, it could fail multiple ways, no output (Hi-Z), output grounded, or output shorted to input, for example.  This one in particular…"
Jan 8, 2014
Bo Wingo left a comment on ArduCopter User Group
"Take a look at the "AC3.1 & blown 3.3V regulator" blog post to understand the issue of the blown 3.3V regulator and how AC3.1 uncovered the issue.  This information should also help you zero in on identifying whether this is actually what happened t…"
Jan 7, 2014
Bo Wingo replied to Pat's discussion What is the correct way to use Region of Interest (ROI) in ArduCopter User Group
"Have you flown this mission? I'm curious to know what the outcome was. I created a similar mission and it appeared to me that the aircraft pointed at the designated ROI, then flew to the next waypoint without changing yaw. Let's say the ROI was due…"
Dec 28, 2013
More…