Okay guys heres the what's going on. I'm looking to rent a drone off Fat Lama, people are renting out a variety of drones. Theres the Mavric Pro, the phantom 4, the inspire 1 v2 and a few of the parrot drones. I've used the phantom 4 before, its epic
Read more…Hi all,
A bit of background info about myself:
Im new to the whole world of drones, but I have a slight background of flying RC planes in my younger days.
I run a website that is orientated around Kiteboarding and iv been creating videos for the website
Hi everybody,
I have issue with flying a quadcopter with Pixhawk as the flight controller. When I apply throttle only using a Futaba transmitter, the ch1out, ch2out, ch3out, ch4out status of the Mission Planner are different, 2 of them are similar to
Read more…I'm working on getting a Skywalker X6 to fly missions. I made a simple square box with waypoints, and set the altitudes low since it was my first auto mission.
Auto takeoff set to 12 meters,
Waypoint 1 set to 12m,
waypoint 2 set to 20m,
waypoint 3 & 4
I know this is a toy drone, (but a fun one) any I've flown it a handful of times and now when I plug in any batter there is no power to the receiver board, nothing happens at all but if I reverse the polarity (probably a bad idea) to the top of the b
Read more…Hello,
I am just getting into the field of UAVs, telemetry, antennas etc. and the following came up:
Recently I had some trouble getting a stable signal with the Pixhawk 433MHz-Telemetry modules with the standard dipole antennas. Therefore I did some r
Read more…We are building a quadcopter using KK board 2.1 and Transmitter FS-i6 for a project. We have carried out the initial calibration of the ESC individually successfully and yet are unable to arm the motors by holding the rudder to the right with minimum
Read more…helo guys, i need your opinion about my current final year project. its about design and development an IoT quadcopter using arduino and control via wifi..
i need to know is it possible to control the quadcopter via the web page only or i need also t
Read more…Anyone know if this will work with the 3DR data modem?
http://www.ebay.com/itm/282333547150?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649
Read more…Hi friends,
I'm struggling with this problem. I have Xuav talon installed with my APM2.5 with complete setup and telemetry.
I planned a mission uploaded it and took-off in Auto mode. After completion of the mission i landed it and uploaded second one
Read more…HiFlew my hex x a few days ago and it flew great. Over 50 mph and very stable. Pixhawk came out of an Iris+. DJI e310 kit.The following day I was getting compass errors. Calibrated it several times and it was okay. Took off and it was very shakey. Th
Read more…I am converting a Skywalker X8 into a VTOL quadplane. For ease of assembly I would like to integrate a connector in the orange parts that connect the wings. What connectors do you suggest? It needs to connect two thick power leads (+ and -) for the q
Read more…Hi,
I've installed Arduplane 3.7.1 into a Pixhawk. Everything seems working fine except the altitude. The altitude fluctuates all time. My plane is stable on my desk and altimeter is not stable. It changes between -1m and 1m. Sometimes it jumps 30cm.
Hello all!
As the title says. I've found the default parameter range more annoying than helpful, especially for PIDs. Why wouldn't 0.7 be valid for Pitch_P? Also it won't let me set the angle P to 0 (which is part of the suggested manual PID tuning pr
Read more…Hi all. I'm using arducopter 3.4.4. firmware with a pixhawk 2.4.6 flight controller, and using a radiolink AT9 transceiver.
When I do the radio calibration in "Mission Planner", I notice that the throttle levels are reversed. The throttle stick is pul
Read more…Anyone know why I can't see full parameters list anymore. I can't seem to find the advanced view checkbox in the planner page? I would prefer advanced view as the default.
Read more…I recently bought the "ARF combo" version of one of these: https://www.fpvmodel.com/hugin-ii-electric-powered-uav-2-6m-platform_g46.html
So I got two large boxes a couple days ago with airframe components, motor, ESC, servos, and about 15 different f
Read more…I am 70 years old and 20 years ago I was into building nitro off road racers. It is reasonible simple then. Now it appears drones are going the way of Microsoft and Apple with the larger companies( some tied in with Apple) are tying their gear in so
Read more…Hi,
I am trying to do hardware in loop simulation of Quadcopter or Plane aircraft using PX4 autopilot, Flightgear, QGCS/MP ground control station and RC.My problem definition is:
