Hello every body
I want to make changes in the battery failsafe method of copter V3.3.3
I want to know that how I can do that?
is there any documentation to get help from
thank you all so much
regards
Read more…Hey there.
I wanted to know if there are some alternatives for people who don't want to build their own quad or don't want to spend too much money on an expensive camera drone like a Phantom 3.
I've research a bit and found out some really cool yet che
Read more…Hello everyone,
I am a little confused about editing the mission planner. How can I write 10 seconds precise altitude values to excel file?
Read more…Hello all,
I own a 3DR IRIS+ with the Pixhawk controller. I would like to connect an Olympus Stylus Tough TG-4 to the Pixhawk, in order to be able remotely trigger the shutter from either the Tx (FS-TH9X) or Mission Planner.
Where should I start in my
Read more…Have someone tested this? I would like to have telemetry data in my reciever as for my Tali H500 original.Any ideas if this is possible?Have someone tested?
Read more…Bought an SX260 a while ago for mapping, but never ended up using it beyond a couple quick test flights. Like new condition. Complete with box, etc. These are sought after because of CHDK and NDVI conversions. Asking $200.
Please email me at robert
Read more…Hi every body
I have a question about magnetometer callibration
for callibrating magnetometer we have to spin it around while it is installed on the copter
now the problem is that when the copter is big, like when a S1000 copter is utilized, we can not
Read more…I am attempting to get a Lightware sf10/a rangefinder working on my 3dr solo. For the basic setup i have been following this guide http://ardupilot.org/copter/docs/common-lightware-sf10-lidar.html
When I hook everything up to a standard pixhawk and fo
Read more…Hello,
it's been a while since my last discussion, especially because I have been very busy building up my hexa and during this period I haven't had any particular issue.
so far so good until three days ago when I tried my first take off, basically whe
Read more…Hello,
I realize there are other posts of others trying to decode mavlink messages but all the examples I seen they are doing it different than I. Right now I have captured all traffic between my drone and controller and saved it to a PCAP file. Usi
Read more…I love sunset(and sunrize) pictures so much!
And I love aerial photos even more, so a combination of the two is really something else for me.
I made this compilation of my favorite images, I bet you'll enjoy!
Here you go:
dronesbuyer.com/29-beautiful-sun
Read more…My x4 quadcopter with Pixhawk is losing altitude when traveling between waypoints in Auto mode. Once it gets to the next waypoint (where it is told to delay 2 seconds), it regains the altitude it was supposed to be in through the path. This goes on b
Read more…Hello, I am attempting to create a small-area survey grid for a 3DR IRIS+ for a 15mx20m plot.
I have set the camera's sensors, the altitude, speed, heading, et cetera, but will be triggering the camera via a remote device (not using the transmitter or
I have setup (mostly) a Pixhack, but I cannot get any form of RC detection. Have spent quite a few days trying to fix this, and I both hope and am worried I have missed something simple.
The Pixhack is calibrated for everything else (compass/gyro etc)
I'm new to Pix4d. Are satellite maps supposed to look like this? Thank you for the help.
Hi everyone , I want to use my pixhawk on a gas engine rc plane, preferably the 2.2m hugin/ 2.6m mugin. But some folks have told me that pixhawk cannot take the vibration. Even if it does during take off there are chances it may just fall out of the
Read more…Does anyone know a way to replay the pixhawk dataflash like you can replay the telemetry logs?
Read more…pixhawk ArduPilot RTL or when in auto pilot settings
do i need to set the servo end points so the pixhawk so it does not over drive servos and break off the servo arms or does it set them when you do a radio calibration
Thanks
Read more…hi all
i firstly compile px4flow completely in ubuntu console,
and then i open the CMakelists.txt file in qtcreator IDE, and keep the default configuration,
build the project and run the code. results show something is wrong with eclapsed warning.
can yo
I have been doing some testing (outside the US) that involve very high altitudes - 1800 meters or more. The climb takes no more power than coming down. Even though going up takes more power per minute, coming down is slower, so the total power consum
Read more…