Hi,
everything is in the title :-) Here is my c++'s code:
if (g.RTL_altitude_cm > 2000 && g.RTL_altitude_cm < 3000) {
}
How does this look like? Do you habe a better solution?
Cheers,
M.
Read more…HI,
Is there a standard PID parameters for the Talon with the wing extension which work on every Talon?
Will the weight affect the PID parameters? Example a 3kg Talon or 4Kg or 5Kg, more batteries of course.
Using the Pixhawk and Ardupilot 3.5.0
Read more…Using only telemetry radios for the link between ground station and aircraft, is it possible to configure ArduCopter to arm and fly without an RC transmitter and receiver in the loop?
Read more…I've been doing a lot of mapping using mission planner to set up the lawnmower pattern over the subject area. Things are going well, but most of these jobs need every bit of efficiency. To that end, is it possible to perform a banked turn at speed
Read more…I've been looking at using the antenna tracker for FPV.
Part of my setup is that I fetch telemetry via my TBS crossfire and collect to via bluetooth from the transmitter.
Given that I already have the mavlink data 'on the ground', how would I make the
Read more…Hi,
I ordered a pixhawk and emailed support to check hte status of my order, but haven't got a reply. I'm surprised there isn't a link to the tracking number on the order page etc.
Also, I can't find some products in the store. The links throughout
I just installed Mission Planner from the download site and installed it. I had no errors during the install but when I went to launch it I received two popups. I attached the screen shots to this post. They say there is "A Major error" and there is
Read more…I have a brand new, genuine 3DR V2 telemetry module for sale along with a used Event38 Bluetooth Bridge so you can connect to your UAV through Bluetooth using your Android or PC.
The 3DR telemetry module came from an Iris+ I purchsed but I have plenty
Hi, I need another one of these 20amp 3d robotics ESC's(see image).
Does anyone know where I can order one or find the equivolent? It reads DDT-30A-20. Any ideas?
Hi,
Anybody have an idea where I can get a cable that connects my Pixhawk to a telemetry module? I can't seem to get them out of 3dr anymore.
Thanks!
Dean
Read more…Hello,My plane is an old balsa Lazy-Bee:(I use this to build experience with ArduPlane)All up weight : 1500gWinspan : 1440mmWing area: : 42dm2Battery / Engine : 7 cell, NiMH Outrunner Graupner 390Prop : APC-E 11x7Static thrust : 1140gThrust/Weight ra
Read more…Morning everyone.
I am still waiting for my radio and wanted to test my drone via Mission planner and a Joystick and managed to calibrate the drone via Mission planned
After several crashes I noticed that the calibration is not "saved" and that every t
Read more…I'm struggling a bit here, and I apologize if this has been discussed, but I was unable to find anything relevant on the topic. Thank you for your help, everyone.
Here's the scenario: I am running Plane on a Pixhawk, all the latest f/w, controlled by
Read more…Hi, I am a freshman of drone and plan to build a Pxhawk drone and also like to use Pixhawk to control LED navigation light and strobe light instead of an independent LED control kit, like this or many other kits.
By other discussion, I learn Relay Swi
Read more…Dear all,
I use to fly a Skywalker X8 for AUTO mission with with an onboard Pixhawk and the last artduplane firmware, and I'm still struggling about the best way to have a reliable airspeed. On the one hand, I flew once without using any airspeed sens
Read more…Hi all, I have just changed my firmware 3.3.3 for my OCTA_FRAME (H) from the stable 3.3.3 to IR Lock 3.3.3.
I am now being bombarded with horiz-errors:-
PreArm: GPS horiz error 5.5
PreArm: GPS speed error 1.2
PreArm: GPS speed error 1.3
PreArm: GPS spe
I can upload initial software to my Pixhawk but i can not get in Contact in flight data. I get the message:No heartbeat packets received.Do I need to have a Micro SD-card in the controller?
Read more…Does anyone know if these antennas will work with the 915mhz radios?
Thanks
Read more…The Solo Gimbal looks very good and the price just dropped to $200. (https://3dr.com/3-axis-gimbal/ )
Has anybody had success integrating the Solo Gimbal into their custom Pixhawk controlled multi-rotor platform?
I read some place that you had to use
Read more…HI FRIENDS JUST BEFORE I OPERATE MY QUAD. THE BOARD WAS APM 2.6..FIRST OPERATE GOOD 2 MINS LATER I INCREASE THROTTLE NO RESPONCE, SUDDENTLY DESEND AND CRASH.THEN I HAD CHECK MISSION PLANNER THE MODE WAS ALTTIUDE MODE BUT I OPERATE IN STABILIZE MODE
Read more…