i have logged my flight data into the mission planner and it shows number of lines for a time period.
i'm interested in the IMU data , where it shows 7 columns,
3 for the accelerometer , 3 for the gyroscope , and the 1st one is TimeMS.
i want to know h
Read more…Hi..
I want to trigger my camera with Pixhawk by CHDK such as these links:
https://api.ning.com/files/db4JtL*UowHxDeGJ3*-gfXx83xkdjpMyGOBPK*xoMIKjlQ
Read more…Hi,
I want to run Mavproxy on custom board like any cross platform.
and i want to run mavlink simulator in my PC.
anyone can you help me on this how to cross compile mavproxy or is there any open source simulator that should run on PC as drone.
Read more…Hi all
I am using xplane 10. APM 2.6 and MP 1.3.21 on the same PC. I tried yesterday all vintages of HIL firmware. I think the newer versions do not work. Could be wrong. Think I went back to 2.7
I have added the info required in Xplane to get the simu
Read more…
I am using xplane 10. APM 2.6 MP 1.3.21 on the same PC. I tried yesterday all vintages of HIL firmware I have added the info required to get the simulator work and get the following error message I do not get any data in the simulator I have never b
I am currently planning to build a PixHawk powered Phantom. I know this has been done before in some regards, but I wanted to share my process and build as I move forward. Here is the list of parts and links:
Read more…I spent hours trying to get this working. XPlane 10 is installed, Mission planner is installed. I have input all the setting for Xplane as suggested on youtube and the forums. I downloaded the HIL firmware for the 2.5 mega amp board. I get this erro
Read more…After upgrading to APM Copter 3.2.1 and doing all the calibration (Radio, compass, accel, flight modes, failsafe) I am unable to fly more than 1 ft off the ground. This is peculiar because I was previously flying with the QGroundControl firmware and
Read more…I have a 250Quad I just built, flys just fine. All other aspects of mission planner work fine, but when I try to see any logs, all I get is endless streaming garbled after I hit connect. It will never stop. (I'll paste some in here at the end in c
Read more…Hi guys,
I had a very heaving landing in RTL today - the descent was much faster than usual, it literally almost dropped out the sky. I suspect my battery failsafe is set too low and the voltage tapered off quickly as the battery ran out and that was
Read more…Hello~~
I'm trying to take pictures with my Canon S100. But when I follow the tutorial (http://planner.ardupilot.com/wiki/other-project-and-common-topics/common-optional-hardware/common-cameras-and-gimbals/common-chdk-camera-control-tutorial/), I meet
Howdy All,
I have been learning Mission Planner and am now at the point of trying an actual mission, and I have a couple of basic (as in obvious to the experienced user)...
I have a mission all set up with 4 waypoints, the first being near where I inte
Read more…Hi everyone,I'm looking for a replacement for my 3DR GPS.I never got a good HDOP and sats number with it.Maybe it's me or maybe it's faulty.Anyway, time for a change and there must be better options out there.What GPS should I buy?If it has a mag, it
Read more…I have been trying to setup auto tune via ch6, but the interface will not save my inputs.
I follow the autotune instructions and when I write ch6 option for say RLL_PIT_P with min/max values, write parms, and refresh parms the settings go away.
If I us
Read more…Hi everyone !
I am using dji Mv2 for my hexcopter, i want to use it for making map of my village. how can i get accurate latitude and longitude data. Do i need a GPS logger of something else plz reply
Read more…I've been looking around at different cameras that can be used for image analysis (NDVI, multi-spectral measurements and the like). It seems one of the important aspects of this kind of imagery is knowing the light you have at the time of image capt
Read more…Can someone tell me if I have a vibration issue? Its hard for me to tell.
Read more…I have a new Pixhawk build.
When doing the Compass and GPS Calibration in MissionPlanner , shouldn't calibration be done outside where you don't have electrical interferences ?
My problem here is Mission Planner is installed on my Windows 7 PC (can't u
Read more…After upgrading to APM Copter 3.2.1 and doing all the calibration (Radio, compass, accel, flight modes, failsafe) I am unable to fly more than 1 ft off the ground. This is peculiar because I was previously flying with the QGroundControl firmware and
Read more…
