Hello guys,
As I do not know much about communication protocols, this is maybe a basic question...
For a classic Futaba 2.4ghz remote control and receiver for instance, I know that no-one else can just come and hack into my plane, on purpose or not, as
Read more…I plug 3DR 914 MHZ to SamSaung Glaxy Pad 4. The green light on the radio was not light look like not powered and cannot connect to Mavlink. But I plug into my SamSaung Note 3 phone is lid and connect. Any idea what I am doing wrong or SamSaung Pad no
Read more…The accelerometer readings from my MPU6050 drift over time. See the attached graph. Throughout, the quad sat stationery on the ground, and only the flight controller powered up - no power to motors / ESCs.
Quad frame accelerometer X, and Y readings (
Read more…I cannot get the PIxhawk to execute position hold in 3.2 or in 3.2rc1
I have this same problem on two copters, each using a different radio (TARANIS)
and each has a Pixhawk, one on 3.2 stable version and one on 3.2rc1
they both do the same thing.
I hav
Read more…Who is responsible for the online store setup, order and shipping process? The process needs some improvements.
1.) Once an order is placed, send NOTIFICATION that the order is HOLD!!!
2.) If an item is backordered, send NOTIFICATION that the item i
Read more…Good dayI am looking to get the best bang for money, i found many mainstream drones to be way overpriced so am on a mission to do this from scratch, where can i get the best prices on a frame, which hk alternative would be best, what should i not ski
Read more…Hello All , i need to trigger the Sony A5100 from pixhawk.
Can anybody tell me what is the pinout of the USB to 3 pin cable?
Can i connect the cable directly to Pixhawk or i need some other component?
Thank you , regards!
Cristian
Read more…hi, i have a quadcopter with apm2.6 , the transmitter and receiver are both turnigy 9x v2 (same pack) , and the esc's are turnigy30A.
i have all my ESC's calibrated and flew my quad before. but today, only the ESC connected to ch3 (throttle) didnt wo
Read more…I have been trying to install windows drivers for the PX4Flow. I have followed the page https://pixhawk.org/users/px4flow_windows_driver and everything looks just as described, and drivers are from 5/19/2014, but when it loads the drivers, Windows 7
Read more…Hello everyone,
A week ago, my Pixhawk was working fine, i loaded Arducopter 3.1.5 FW, everything O.K,
Im using this configuration for powering:
http://diydrones.com/profiles/blogs/how-to-guide-pixhawk-with-6s-batteries-4s
Yesterday i turn on the board
Read more…Hello everyone.
I have an 3DR APM Plane
My goal is to configure the camera trigger for CHDK.
What I know:
I've being searching and looking at CHDK topic in adupilot website. And without s
Read more…Hi,
Is it possible with the bluetooth module for the pixhawk to communicate with a arduino based ground station ?
I need to send a few codes to the arduino.
from copter to ground station:
first code (binary or something) meaning landed, motors switched o
Read more…I have been seeing a lot of radio interference recently on my spectrum analyser. Operating in and around a commercial port with a highly sensitive military base close by is probably asking for trouble. I was operating in the Limassol Marina and Comme
Read more…Anyone running a gimbal on their helicopter?
Curious if someone found the best route for taking vibration out of the camera while in flight and in a hover?
Care to share?
Read more…
I have a 650 quad with 12" props on 700kv motors that felt pretty smooth with stock settings. I ran the autotune and it became very very twitchy. I backed off RC feel and roll/pitch sensitivity but it still feels very twitchy. Any advice? Should I ta
Read more…Hi Folks
I seem to have a unique problem
I'm running a EZUHF Rx on Arduplane 3.20 and want Link Quality and flight modes using PPM in from the RX
I had flight modes working fine on Channel 8 to the APM 2.5, have moved the mixes to Channel 5 and they are
Read more…Presently have Pixhawk installed in frame, and have Futaba 10J radio with the R3008SB receiver installed. The receiver is plugged into the SB port(2nd from left pin set). Radio has been bound to receiver. When powered on, the MP message is Pre-arm,
Read more…Hello All,
This is my first post on DIYDrones though I have been active on MultiWii forums for a long time. I have been working on a very low-cost, aerial mapping UAV and documenting my efforts at- http://publiclab.org/notes/code4maine/08-05-
Read more…Hello guys,
MP 1.3.17 build 1.1.5472.17896
When preparing a mission, and when i click on "View KML", it is trying to load http://127.0.0.1:56781/network.kml and gives an error msg.
Anything I can do about that ?
Thx
Read more…Hello
Prior, the code below would start the camera stream with no trouble. Now, it locks up the system. Anybody run into this before ?
raspivid -t 0 -h 720 -w 1080 -fps 25 -hf -b 2000000 -o - | gst-launch-1.0 -v fdsrc ! h264parse ! rtph264pay config
