Hallo,
I am new to this forum but not to multirotors.
Since version 3.2 there seems to be a problem with the RCMAP-function.
I am using Graupner mx-20 Hott which has different channels than the Mission Planers wants.
I used to adjust that with RCMAP and
Read more…If I use the Auto TakeOff function (for ArduPlane) at the beginning of a mission,
and I set the Altitude of the Auto TakeOff to for example 20 meters;
will these 20 meters be 20 meters above ground level or 20 meters above sea-level?
Thanks a lot
Felix
Read more…I've been stumped looking for a place to buy bare lipo batteries! my goal is to make small 3s packs with individual connectors for each cell, so they can be charged as 1s3p but discharged as 3s1p.
I have found small and medium (200-1000mah) cells on
Read more…Howdy all,
I am currently building an RC/Autonomous Mower and have some questions I could use some help with.
Currently I have the mower fabrication complete and as of yesterday I have the mower driving around in RC Mode!
(I have attached a few quick ph
Read more…Has anyone used guided mode? I was trying it out today and all is good until it gets to the target from there it wants to spin around in a circle like it's lost.
Maybe I missed something but is there a setting to change the behavior of the AC when it
Read more…
I have been trying to reach someone who might know my problem by posting on my own discussion thread in "miscellaneous" on my profile page. I haven't gotten very many suggestions or ideas, so maybe this is a better category. (except for test flig
I see arducopter has two possible tri-copter options; which is best? And what does it mean when the second option "doesnt need a code change"?
It's for a small 300mm foldable - the HK trifecta to be specific.
Read more…Arduplane V3.2 and APM 2.6 3DR, gps/compas 3DR. It was working fine until today.
Any idea of what could be the cause please ?
Thank you
Read more…I'm selling my 3DR Y6. It's a nearly RTF system (just add your radio and a battery), and is in great working shape. I'm getting 12+ minute FPV flight times with a 4S6000. Would love to keep flying this bird, but need to upgrade my camera beyond wh
Read more…Hey all,
noticing very strange behaviour when I have the following setup connected:
Pixhawk with a v-tail plane connected to channels 1 and 2, with the Mediatek GPS from 3DR connected. When the GPS has a good fix nothign weird happens, but the moment t
hi all,
i am using the following setup on my hexacopter. i hav made the setup complete, calibrated accel,compass,radio. when i arm the hexacopter and raise the throttle, motors seem to spin, on full throttle it slightly moves backward but no lift.
fram
Read more…hi all,
i am using the following setup on my hexacopter. i hav made the setup complete, calibrated accel,compass,radio. when i arm the hexacopter and raise the throttle, motors seem to spin, on full throttle it slightly moves backward but no lift.
fram
Read more…hi all,
i am using the following setup on my hexacopter. i hav made the setup complete, calibrated accel,compass,radio. when i arm the hexacopter and raise the throttle, motors seem to spin, on full throttle it slightly moves backward but no lift.
fram
Read more…I believe fence or geofence to be one of the most amazing, useful safetly features of this firmware.
Thanks for everyone's hard work to make this possible!
With fence on,
Now, when the the target altitude is reached (or breached) the copter enters into
Read more…is there a way to connect the TM1000 to pixhawk ?
the purpose id to have basic telemetry on the Spektrum TX screen .
anybody have DSM2 or X , hardware spec to see if the Tm1000 and satellite can be daisy chained to the Pixhawk port?
thanks
Read more…Hello...
I have been searching for 3 weeks with no succes, so here goes:
1. How do I display parameters (AmpDrawn, disttohome, etc) in the PFD window of Mission Planner??
2. Where did Grid planinng go from Mission Planner? In the previous verison, in FL
Read more…Hi!
I'm super new here and to drones in general. I have a quadcopter kit from China - fairly basic frame / kkmulticopter board thing - everything was going fine: building, calibration etc - only thing I had left to do was put the heat shrink on the ES
Read more…I am using HobbyWing 30A Platinum Pro opto ESCs and the motors are HengLi W48-30 KV370.
When the quadcopter gets to a certain RPM the whole thing oscillates violently and also causes crashes in RTL mode and yaw correction is unstable.
I bought a servo
Read more…In Arducopter 3.2 using APM 2.6 there is a change in buzzer behaviour (from 3.1.x) when arming the FC.
The first time the FC is armed, after power up, the buzzer will beep a few moments before the propellers start to spin. This is a good warning, alt
Read more…I'd like to purchase the OSD kit from 3DR and install it on my 700mm sized helicopter. https://store.3drobotics.com/products/3dr-fpv-osd-kit - sorry for the dumb question but will I need the Pixhawk component as well? Thanks, Mike
Read more…