Hi. All. I've seen the prefetch function for Mission Planner. I'm wondering if there is a way I can just download "all the maps I'll ever need" at once and store them in case I need to use them some day. In essence, I'd like to Prefetch maps for a
Read more…What you see in the picture is what you get.
Software is not included. IMU is brand new.
Let me know if anyone is interested.
Read more…So which of the many parameters can I adjust for this? I've done the manual and auto tuning. It flies like a dream. Rock solid. But on the ground it will oscillate/wobble until it lifts off.
Pitch:
P .165
I .165
D .007
Roll:
P .1
I: .1
D: .004
Stab:
Pitch P:
It's not released yet, but coming soon. just curious to know what others think about this new plane.
here's the youtube video.
https://www.youtube.com/watch?v=3vfb-ANWUFQ
Read more…I was at a multi rotor meet, had just done a auto tune and things were nice and stable. That's when the quad decided it would do a back flip and crash to the ground...
You can see in the logs the throttle, pitch,roll and yaw goes crazy
Can anyone deter
Read more…I thought the problem might be with an ESC or motor so I changed all ESC's and motors. The problem still persist.
This is a dji F450 with extended aluminum arms (550mm) and an APM 2.6 with external compass. The first setup ESC's were stock dji 30amp O
Read more…I'm sure I'm not the only one that caught the Flite Test video a few days ago about "Flite Fest". Is anyone going?? I'm looking into driving 9hours to be there with a carload of RC gear, and would REALLY like to see some Drones!
Maybe someone
Read more…I have a Pixhawk powered quad here which will slowly yaw clockwise or counterclockwise, depending on the current heading. It seems if the heading is less than 180 degrees, it will yaw anticlockwise, and if it's more than 180 degrees it will yaw clock
Read more…So I was test flying the X8 octo today and doing some auto tuning. In the process, it suddenly jerked to the left roll and weaved on pitch. As if it was starting to freak out. In turn caused me to freak out as you might guess. I just did the latest
Read more…Hi - I am trying to set up my Pixhawk to trigger a camera using Arduplane and when I tried to test the voltage step-up circuit described here I noticed that there wasn't any voltage across the +/- aux out pins. In fact the only set of pins with a vol
Read more…Hi, I can't find compassmot at the setup mode. Is the compass motor calibration at optional hardware the same?
Read more…Is it possible to use one ground station radio to controll multiple vehicles at the same time?
Can I use multiple radios next to each other simultaniously (ground station-radio combinations)?
Read more…I have a Spektrum dx6i and I was able to configure it for failsafe with Mission Planner (signal lost).
It works fine with Mission Planner, when I power off my TX, failsafe is triggered and RTL occurs. I did test on flight and works great.
But when I am
Read more…My control is through a spektrum ar6100 with signal lines to the input of the APM. I have it setup per the apm wiki in the futaba order (Aileron, Elev, Throttle, Rudder, etc). When I power on the APM the ESC makes the tri tone I am used to on a arduc
Read more…My Tricopter has started yawing by itself in the hover which is very odd, I thought the APM's compass would keep it pointing in one direction?
Loiter is pretty perfect except for the slow yaw.
Motors are flat and rotating the right way. Everything else
Read more…Hi,
in Mission Planner its only possible to get a Serial NMEA Output with relative Altitude. I like to Track my Quad with a GPS Based Tracking System that only can us NMEA0183 Format. The altidude is over MSL. Is it possible to Change the Serial NMEA
Read more…Hi community.
I have an issue with my setup and RFD900.
When the RFD900 in ON (27-30 dbi of power) the servos are tremoring and when RFD900 is OFF - all working fine.
Somehow RF noise affects to the servos or servo wires or maybe APM 2.5 and there is
I have been following these instructions in the developer site here:
http://dev.ardupilot.com/wiki/setting-up-sitl-on-linux/
All is good with no errors until Step 6 - Start Up
I get the following - the problem is that SITL can't make properly. What am
Read more…Hi
I had my PixHawk on a DJIF550 Hexa Frame with the new DJI E300 propulsion kit, controlled with a Spektrum DX9 and a HobbyKing R800x receiver that has SBus out connected to the PixHawk RC-IN port, and was working ok, after some tweaks.
Radio calibra
sorry for that maybe stupid question but, after the mission planner update (1.3.1) I cannot find anymore the CLI console....
I have a MSDOS window with :
Open MissionPlanner.GCSViews.SoftwareConfig SWConfig
Open MissionPlanner.GCSViews.ConfigurationVie
