I've just updated to 2.7,
since the update i have a small problem with the camera mount.
Before i could use the CAM_R_TRIM to level the mount, this time it has no affect :-( I tried to set 1700>Wright Params then read and it's accepted the changes but
Read more…Hey folks... this is just informational. You're welcome to look into the data for more lessons learned, I'm sure there is more to learn from the telemetry logs, but mainly I simply wanted to share an amusing but not very productive day. Too often we
Read more…Hello again,
Now i write asking for help about xbee 868 and airspeed.
I have an airspeed:
https://store.diydrones.com/Kit_MPXV7002DP_p/kt-mpxv7002dp-01.htm
When I connect APM to mission planner (MP), MP shows airspeed readings ok. The problem comes when
Read more…I have been previously flying multi-rotor and today I finally got my airplane finished and had a few good PID tuning flights. So I am mostly flying in FBW_A to get the PIDs tuned. One thing that bugs me is that the Mission Planner readout is absolute
Read more…I using a APM with an X8 (wing with elevons)
R/C controls function fine in both manual and stablise modes.
The problem is in stablise mode, when the aircraft is banked to the left, the left elevon should go down, and the right elevon should got up, to
Read more…Hy
I just saw in the Arduino code of the ArduPlane 2.5 that there are a lot of "gcs_send_text_P"
example:
gcs_send_text_P(SEVERITY_LOW, PSTR("Failsafe - Short event on, "));
gcs_send_text_P(SEVERITY_LOW,PSTR("Demo Servos!"));
Where do they show up in the
Read more…Hello,
Actually, i control my plane with mission planner, but i would like to try control it with web browser at home.
I don't know if there is any project/version which makes it possible.
Do you know if mission planner has any option to send all data t
Read more…I've just upgraded to Arduplane 2.5 using the APM planner 1.2 onto my APM 1.0. All seemed fine, but when I move the switch towards the pin headers, to start flight mode, and reset, I just get a sold green LED, nothing else lights up (not the regular
Read more…Looking at adding still photography to my Multirotor but dont know what camera to go for. I have seen that some of the canon cameras have the software hack option,but how will this allow me to oparate the shutter ?
I have also seen these http://www.ge
Read more…Hi guys, I did a jumper to enable disable onboard GPS, I didn't like has to solder-desolder the jumper between GPS paths. I hope this can help someone. All made with components of APM2's bag.
Hello there,
I am excited to announced that i've build my first ArduCopter. But i am twice much upset to let you know that it needs a Doctor. :) LOL
Successfully, i updated the APM2 with the ArduCopter 2.7. However, i am have lot of issues with the qu
Read more…Hi,
I buyed 6 new motors from diydrones store, all of them works well except one.
When I calibrated all the ESC, one of the motors don't work properly. It moves randomly and produces strange sounds.
You can see here:
I tried to change the ESC with the sa
Read more…It took me a while to notice this, in fact I did a test flight before without noticing the problem, so I'll post a video.
The compass in my APM2 swings back to between 20 and 50 degrees as soon as the unit sits still. It swings "correctly" while the u
Read more…Hy
I changed something in the code in the Arduino IDE. I tried to use the APM_config.h but this has no affects on the values....
Is the APM_config.h disabled for the version of ArduPlane?
Thx
Andy
Read more…Hello all,
I am working on some unmanned vehicles and it is required to have both video and telemetry transmissions. I would first want to look for some modules that are capable of sending both of telemetry data and video link. Do you have any suggest
Read more…
In just a short while, ArduCopter 2.7 will become available for download in Mission Planner. As we worked on ArduCopter 2.6.1, we saw that it had several new and compelling features (as well as many bug fixes and improvement) so it was decided to
Is there a way to reduce the start up speed of our motors in APM2?
Thanks,
Rick
Read more…I'm delighted to announce the release of ArduPlane 2.50 for your flying pleasure. This release has a lot of advances to some of the core ArduPlane code, and should be a big improvement for many people.
Perhaps the most important change in this relea
I managed to drop my 4S battery cell voltages way below 3.0 volts. Do you think the LiPo should now be thrown to carbage box or should I still try to charge it?
Read more…Is it possible to connect the RFD900/3DR Radios directly to Arduino?
The idea is instead of connecting the telemetry radios to a computer, I'll connect it to a microcontroller that will be able to decode the received data then send the decoded data t
Read more…