Hi there
Got my APM loitering fine but was hoping to get the radius a bit smaller. At the moment I havent changed a thing on the loiter PIDs so havent a clue where to start. It flys perfectly balanced as I have adjusted the PIDs for that side of thing
Read more…Hi
I havea problem with the MP that I cannot zoom in to any location. If I zoom too far I get this error (see the attached picture)
Problem is with both my PC's.
Any suggestions?
Read more…Can someone please confirm what are the units of measurement in the mission planner HUD, and whether they are changeable, and if changeable how is it done.
As a manned aircraft pilot I would expect to see airspeed in knots, and altitude in feet. But
Read more…This all very new to me so there's a big learning curve. I am fitting my ArduPilot Mega 2 in a large nitro plane I have. I have also got the airspeed sensor for the APM2 which I will connect.
A few questions that I'm stuck on:
How do I set the airspee
Read more…Hi guys. I just encountered a problem with the most recent update of MP 1.2.1 Mav 1.0 and AC 2.7 update. While trying to connect to establish a data link (USB) to APM2 board it either stops midway (or somewhere near the end) during connection or goes
Read more…Hi
I am wondering if anyone else has had a similar problem?
If I zoom all the way out I can see the map of the world, but as i zoom in, it does not load more tiles and image gets blury untill I get the error message as shown in the picture.
This problem
Read more…Really basic question here. I'm working on building a radio transmitter from scratch, using Tx firmware from elsewhere. I want to build Ardustation into the unit. I'll be having a ~1/16" aluminum plate waterjet cut to hold the joysticks, and obvio
Read more…My CLI keeps doing this. Doesnt matter what position the switch is in. I havnt used the CLI in a few months so Im probably missing something.
Hello,
I've just received my new APM 2.0 autopilot and would like to know how to properly connect it. I've read the Quick Installation Guide on Wiki but I still am not quite sure how to go about it.
I've installed the Mission Planner as has been writte
I was wondering whether the loiter mode on the APM2 can be configured to work with manual throttle input like the Loiter mode of Dji naza ( Atleast mine acts like the Alt hold where you can either fo almost full throttle or sub hover speed. It would
Read more…Basic background on APM2 = 1 week. I have been experimenting with Different PID settings from 1.0 - 3.5 default I = 0.80 and IMAX = 30 without any success. My configuration is dji f450 with Gaui 330x Motors 1050kv and 10" props. Any starting point fr
Read more…Attached is some data I collected looking for the best prop for my stuff..
The APC electric are as good as APC slow fly... that surprised me..
Eddie Weeks
Read more…As you can see I get everything BUT none of it works! All the numbers never change.
MP is version 1.2.1 with MAV 1.0, MinimOSD flashed with the Jun 1st release of the MCM and HEX files (multiple times with the FTDI cable from DIY drones).
2 stage powe
Read more…In all of the documentation it says the maximum, and minimum, roll and pitch angles are in centi-Degrees.
eg,
The maximum commanded bank angle in either direction
How
Read more…Folks, I have sore fingers and a scratched wall :)
I've just loaded 2.7 on my APM2 and needed to reset the gimbal settings.
The quad was powered with the lipo and disarmed with the tx standing next to the quad.
As I put the gimbal's servo cable onto the
Read more…Hello,
Downloaded MissionPlanner32-1.2.msi, won't install. Install Shield goes through its paces, Around the "validating" step it says "rolling back" and uninstalls, ending with "error....etc."
This is a Win XP machine, 32 bit. Installed .Net Framework
Read more…Hi,
Just updated to 2.7 on my Y6. However, I still seem to have this random issue where the mag (DIYDrones HMC5883L) fails to init when I hook the battery up. In mission planner I get a slow rotation of heading which does not respond to the heading o
Read more…Hello:
I have the following error when I upload the flight plan. The telemetry is fully operational, and I can´t upload the flight plan with usb and with modem neither. Anybody know what happens? Thanks in advance. Jesús
I thought that up until very recently there was a top content section on the top right of DIYDrones page. I see the groups section now but the top content seems to have gone.
Is it just me?
Read more…I dont want to litter the place with nonsense, but I'm trying to learn and have hit a brick wall. I took Jean-Louis' tricopter code which runs on IMU V2 and tried many different ways to add IMU V3. I assembled a PPM encoder, Cut up an old GWS Rx fo
Read more…