Arduplane CLI entry
I cant enter the CLI settings.
3X enter doesnt do anything.
in the MP 3X enter makes the MP stuck.
Read more…
2 Replies
All Discussions (17281)
Sort by
Aruplane/X-Plane Simulation Problem
I am trying to get my Arduplane working in simulator mode (X-Plane) and am not having much success.
I have a Hitec RC system; a 2.4G Optic6 Tx and an Optima7 Rx. I have servos attached to the
four control channels. The system is in manual mode
I caref
Please help with electronics build list
I have put a build list together (minus the frame) For a FPV and UAV project.
( I have not decided yet if it is going to be a quad or Y6 config.)
As I live in Europe, I cannot use 900mhz. I was going to use 2.4ghz for the video and 72mhz for the radio,
Read more…OCTA-V vs traditional OCTA for AP
Hi,
I need advice on what airframe to choose for Aerial photography Octa.
It will be carrying about 2.5-3.5 KG payload of gear
What are your inputs on OCTA-V versus traditional OCTA (spider shape) ?
I haven't seen many OCTA-V projects, but one is impress
Read more…Licensing for wireless video
I am looking into using a wireless video system and understand that I will need a ham license. I will be getting that but I would like to integrate the video system into my professional work. I work for a public museum and from what I understand it i
Read more…Works indoors, Beeps outdoors
Hi,
I'm trying to get my maiden flight going!.. I performed a hand test inside my house (74°F, 23°C). I took the quad outside (26°F, -3°C). When I power on the quad, it started beeping similar to when ESCs were not calibrated.
Now after coming back ins
Read more…Quad rolls to the right
I have managed to get my quad somewhat up and running today, but I still cannnot get anything even close to stable flight without roll stick input. It's a stock arducopter 3dr kit running APM1 with an atmega2560.
Takeoff requires about 20% left roll i
Read more…Downloading HIL Simulator for Arduplane
Hi all,
May I know where I can obtain the HIL Simulator source code other than downloading directly from Mission Planner? Would like to make some additions to the code before uploading to APM. Tried to look for it in the git branches but I couldnt fi
Read more…Catalog of Useful User Hacks Wiki
I've started a new page in the Appendix of the Arducopter Wiki. The intent is just to gather up any of the really good hacks that have been submitted by various users in a place where new members can find them easily.
http://code.google.com/p/arduco
Read more…Any interest on DIY mod to slave external LED's to the "motors armed LED"?
I figured out how to successfully drive a large LED bank with external power by the same circuit that powers the "C" LED on the APM 1.4 shield. I am thinking of putting together a how-to Blog post with the circuit, but I'm just wondering if there is
Read more…LiPo Question
Hi,
How to know your battery level whether it is within the safe level during flight? (w/o voltage sensors) Is it a time limit?
The Story:
Before the maiden flight of my Quad, I was testing it a lot :) After some time, I realized the battery power has
Not enough lift on arducopter quad
I assembled my JDrones arducopter kit with the AC2836-358, 880Kv motors and the JDrones 30A ESC with 12x45 props. Everything worked fine (control, yaw, pitch etc) except that it does not get enough lift to get off the ground. Props are on the right w
Read more…Traducción al Castellano de APM Planner
Hola, tal como hicieron los amigos franceses, pido alguna traducción al Castellano de la Herramienta APM Planner, no se si está pensado en próximas versiones la traducción al castellano, pero pienso que tendría una acogida bastante buena, ya que somo
Read more…can not control the aircraft manually in auto mode ardupilot
Hi,
today I try arduplane 2.6. Manual and stabilize mode ok. When I try in auto mode, aileron and elevator can not control manually. Rudder still can. Throttle still control manual (not connect to Arduplane hw).
Do you have suggestion?
regards
Deni
Read more…Arduplane 2.27 from git master branch
Hi all,
I've faced a couple of issues with Arduplane 2.27, hope to find some answers here.
Uploading Arduplane 2.27 from Mission Planner works perfectly for me.
But, uploading Arduplane 2.27 from Arduino IDE does not work (APM does not initialize aft
Read more…Problems on 2 Ardupilot Mega board
Hello!
I don't understand. I have 2 Ardupilot Mega (V1.4 and old version) with a strange problem.
The V1.4 doesn't have any reaction (blue led off) when I power up the board plugged on my receiver, however the receiver get power from the board....
The o
Read more…Log Questions
Hi all
I've had a few very successful flights, but have a question about reading the log.
1. How do I turn on the *ATT record in the log file?
2. Is there a way to reset the log over the XBee connection?
Many thanks
Read more…apm 2 channel 5 output gives wining / spiking servo 6 is ok.
Ok something weird with my apm 2. whenever i put a servo to the channel 5 output of apm2 for camera stabelisation that servo will start to give hight pitch noise and judder. When i put the servo at channel 6 all is well. So somehow the signal comming
Read more…Hot motor problem
One of my motors is getting extremely hot. I was checking the motor direction after calibrating the ESC's and I noticed one of the motors got too hot to touch. All of the others were ok. It only does it when the motor is moving. I tested the temp
Read more…bad attitude from a stationary ArduCopter
Background: My first ArduCopter (APM1/oilpan, mag, no sonar, ublox GPS, xbee 900, hoverthings X450 quad frame, 1000 Kv motors, 30A escs, 10*4.7 props, 4Ah 35C 1P4S LiPo, X cross configuration, code from trunk from about two weeks ago). Had a few flyi
Read more…