Hey guys
Im not sure if this will be any use to anyone, but it is to me. Saves having to use a remote cable for my SLR.
Assemble takes all of around 15 mins including code upload.
Its basically an IR Camera Shutter control using an Arduino uno and a IR
Read more…Hi all
I purchased a Arducopter and im lookign to get the best flight times I can. I have seen somewhere a guy using two 5000mah 3s lipos is it worth going that far? Would two 8000mah 3s lipos be far FAR too much?
Read more…Hi
I have two options for BEC,
1. 4.8V 3A BEC
2. 5V/6V 3A BEC
Which one is better option for Arducopter power supply?
Cheers
Kelvin
Read more…Hi all,I recently purchased and have finally put together my Arducopter from Jdrones.My compass came with wires and plug attached but I decided to unsolder these and attach directly to board as recommended, in doing so have bent two of the pins and p
Read more…Is there a method of having stabilized pitch and roll, with the addition of being able to control pitch from the TX?
Thanks :)
Read more…I am trying to calibrate my radio in APMSetup. I move the sitck and the red bars move. I go through the calibration and everything seems ok. But when I go back to the radio input screen, the green bars don't move the full range on screen and are n
Read more…Hi guys,
some time ago I had a shortcut on my APM, and it stopped working.
here's the current behaviour I'm getting:
with AP+IMU:
if I plug the power as usual nothing happens, not a single light shows, dead.
if I plug via the USB cable on th
Hi all,
I have been experiencing some weird logging behavior by APM. Im running APM 2.26, and im using the default flight logging settings.
After every flight, APM somehow auto reverts its logging settings to the following:
logs enabled: GPS PM CTUN N
I would like to know is there anyone that can recommend me a small FPV camera for my Quadrotor and preferably connected to a micro transmitter. This camera is use for normal video viewing on the ground when Quadrotor is flying.
I came across this FPV
Read more…How do I change PWM values in MP? When I calibrate my radio, the lows seem a little high (>1200). Because of that I can't get to mode 1 with the F Mode switch and I think it might also be the reason I am having trouble arming the motors. TIA, Greg
Read more…This is a new thread for discussion about what we can do to get a very precise Loiter.
The initial thread is here :
My proposition was to use
Read more…Hi, I'm building my first quad and am having problems getting the ESCs to arm. I have followed the ESC calibration instructions, several times, but no luck. On the APM (loaded with the latest code V2.1.0) I get a solid green light indicating it is ar
Read more…Have anyone tested this 20Hz GPS in comparison to the ublox? How is it to interface it with the ardupilot?
Kim
Read more…helo
about 2 years ago I bought an ArduPilot GPS-08785, because of my work I never had time to operate it.
these days I'm trying to start install and operate it as a nav system (without stabilizing) .
I tried to look for instructions and drawings for t
Read more…Hey every1
Im having trouble compiling the AP_OpticalFlow_test.pde in arduino.
The error is as follows:
In file included from C:\Users\Gareth\Downloads\ArduCopter_2.1\libraries\FastSerial/BetterStream.h:16,
from C:\Users\Gareth\Downloads
Tried to fly 2.1.0 (Alpha as called in MP) today. Tried Loiter , which I didnt find particularly good, but noticed that at sonar altitudes (0 to 8 meters) something was wrong, the copter just decended. Thought I should test the sonar in Mission Pla
Read more…Long ago in a galaxy far far away I built an RC solar plane.
http://www.rasdoc.com/splinter/solar2004.htm
I have a lot of switching power electronics on this plane and it was before 2.4Ghz radios were common. The power electronics caused interphereence
Read more…