HELP ME PLEASE
can any one tell me where i can get a electric mechanics for a super scale helicopter?
Read more…
0 Replies
All Discussions (17288)
Sort by
Payload Integration
A search didn’t reveal anything along these lines so bear with me if this has been hashed out before.
The auto-flight systems that have been developed by this community are nothing short of fantastic. Unfortunately, unless just flying for the fun if
Read more…Importance of a clean power supply
I have noticed in the forum a number of people advising the connection of ground (negative power) of all their ESCs to the APM. In some cases some people are also connecting multiple 5 volt lines to the APM in the hope of providing redundancy of the
Read more…IMU Shield Broken
I think my IMU shield died. It was working ok the other day but now the ABC LEDs never flash and the MAVlink won’t connect. I confirmed the switch position but it won’t work.
I have manual control but other modes don’t work any more. In other than man
Read more…Octo coax are supported?
Hi all! Inside the "define.pde" i've found "#define OCTA_QUAD_FRAME", but i never found the connection to APM of the 8 motors in this configuration.
I try to convert my heavy Octo-X to Octo-X4".
Unsteady Throttle
I am in the initial stages of tuning my new airplane. I got FBW_A mode working after adding a little more pitch comp. I tried the FBW_B mode for the first time today and the throttle was not smooth. This is a fairly high powered airplane (GP Escapade
Read more…ESCs in and out of calibration
I have calibrated my 4 ESCs from my 3DR kit on several occassions, mostly via the manual method, but they seem to intermitently indicate that they need recalibration.
I turn on the copter and sometimes, all 4 ESCs initialize nominally, but other times
Read more…Minimum loiter radius
Hi all,
Was testing APM again today.
Needed my plane to loiter with a radius as small as possible.
Set it to loiter at 10m height and 10m radius in Mission Planner.
Managed to loiter at 10m altitude, but the loiter radius was observably larger than 10m
Read more…2.0.55 seems a little wobbly
Below is a gopro fpv.
55 seems alot more "wobbly" than the previous versions.
Im running a std arducopter.
@Jason: im not sure if 55 is tuned for the 3DR.
Thoughts anyone?
G:)
Read more…GoPro "jello"
I mounted my GoPro Hero2 to the top of my 3DR frame using the standard mount and the resulting video was unusable- complete jello. So then I used tripod adapter with the camera and a 1/4-20 bolt to the top and still had unusable jello in the video.
Is
Read more…ArduPilot Mega Dimensions - Updated
Hello,
I am having problem finding the dimensions of ArduPilot. I read in one of the Forum Discussion that i can get all the dimension from Eagle Files (.brd). I have downloaded the Eagle software and open the .brd file. Because of my poor Eagle Softw
Read more…Yawing in wrong direction
I have a stock ArduCopter frame with ArduCopter 2.0.55. I have enabled the mag, and it's soldered as described in the wiki.
It hovers very stable, and yaw is not drifting. However, when I apply yaw input with the rudder stick, the quad yaws in the wro
Read more…ArdupilotMegaPlanner.exe. Unable to find this specific file after download
Hi
While waiting for an assembled A/P Mega to arrive, I downloaded and extracted the APM software - opened it and searched on but could not find the directed ArdupilotMegaPlanner.exe file. I did find a file named ArdupilotMegaPlanner.exe.config but
Read more…APM Power backup
Iv been thinking. What happens when you're in the middle of a flight and your ESCs BEC kicks it.
All power to the APM is lost and so is your craft.
Even if you use a stand alone BEC, you suffer from the same problem.
Has anyone had a crash due to APM po
Read more…APM Not Following GPS Waypoints
I have the HIL firmware loaded and I am flying the plane manual in X Plane simulator. I grab the Home location and draw a quick square set of waypoints about 200m altitude. However, once I switch to Auto mode, the plane doesn't follow the gps waypoin
Read more…Frame Assembly : Possible Error in the documentation of 3DRobotics?
hi,
I find following image in the documentation confusing..
If i understand correctly this is the view from the bottom. with this pin connection configuration, I find impossible to achieve a configuration given in the following image..
I'm assuming th
Read more…Throttle weirdness on arduplane 2.26/ apmplanner 1.1.2 vs. normal on 2.24/1.0.88
Gday,
Things are fine with the old combination of arduplane 2.24/ APM planner 1.0.88
With arduplane 2.26/ apmplanner 1.1.1 or .2, I can't get throttle settings to work.
Have gone through reflash/reconfig cycle a couple of times and always the same.
Summa
Read more…Quad tettering on one axis at hover
Hi,
My X quad loaded with 2.0.55 teeters on a single axis during hover. I have increased the gain of P values for both rate and stabilisation which is has made the quad more responsive, however teetering remains. Aside from this I am pleased with t
Read more…Servo signal converter (spi/i2c/ttl/rs232) with parallax propeller?
I would like to minimize the processor time in arduino and googled some ppm encoder stuff. I found that the parallax propeller has multi core architecture with eight 32-bit risc cores. That device is commonly used as servo controller, but I would lik
Read more…