Hi everybody, i want to know how I change the move direction of attitude indicator in APM Planner. I need to change only that, because the rest of my equipment work very right. Thanks you!
Read more…Does anyone have any recommendation for 30A ESCs that I can get somewhat quickly and affordably in the US?
Thanks,
Pat
Read more…Hi to all, i want to put a camera tomy plane and i would like it to transsmit directly to my computer or other display, i also would like it to use like OSD with all tools on screen.
Thanks.
Read more…I am having problems with the new Multiple Aileron Channels option. It works by radio control but when I tilt the airplane the APM controls the left aileron (channel 1) but not the right aileron. I have tried turning on channel 5 and 6 and it does th
Read more…OK i been looking and cant find what im looking for so im asking for help. Building a projet RQ-11, and need to know a cut and dry setup for the UAV. Best motor, battery, ESC and prop to handle all the electronincs for autopilot, gps videocamera, al
Read more…Tried the 2.0.55 release from MP 1.1.1 today in the gym at work. Previously auto-trim has been the way to get leveling tuned for my AC. This time it did not work.
Before leveling the copter, it leans heavily in one direction after take-off and flies
Read more…I have a quadcopter 3DR and am considering mounting the battery above the frame arms instead of below the arms, and I'm wondering how sensitive the stability of the quad is to this shift of CG?
I realize that this swap of CG from below the arms to abo
Read more…Hi guys hope someone can help me with this..
After another routine fun flight with APM, it stopped working all of a sudden.
With the CLI switch in flight mode, APM no longer connects to my PC. The time out counts down from 30secs and gives this messa
Read more…Hi,
I am currently trying to get GPS signal using Mediatek GPS connected to ATmega1280 as shown in the pictures. Now, Mediateck GPS shows solid blue LED, but LED C does not show red light. In addition, serial monitor shows only "."
'Example_GPS' is us
Read more…Does any one have a good configuration for the Apprentice airframe?
Read more…Ardupilot 2.1 is out and can be downloaded by the mission planner (or with Git). You must have the latest version of MP to be compatible. If you're compiling with Arduino, you must use the "mrelax" version of Arduino that is in our downloads section.
Read more…I feel bad for asking but.... I need to tune Rate P for my Quad using the Ch 6 tuning feature. The values I see when I enable "tune 4" are in the range of 0 - ~40. The typical value for Rate P is a decimal figure of about .14. There is not enough
Read more…The new board introduced in the last month (first Phone Board) and then Ardupilot Mega 2,
will think to me that in the course of next year more improvment will do .
1) I ask to me if you have planned to do a DiyDrones OSD instead to use Remzibi device
Read more…I have purchased from Jdrone the XBee PRO 900Mhz, Wire module for vehicle and XBee PRO 900Mhz, RPSMA module for GCS and which states the following,
"Fully assembled, configured and tested telemetry set. All that you need to make your UAV to talk with
Read more…Why is there a female header included in the kit? As far as I can tell, it isn't used for anything, but meanwhile the telemetry kit instructions immediately call out for soldering a 4 pin breakaway header to the APM oilpan:
Read more…Hi Guys I've got the maxsonar XL 1260 and i find the hight when on the ground is at 20cm but if i lift the quad to about 1mtr it says its at between 50 to 70 cm.
Is there anything i can do to calibrate this sonar to the right hight?
Thanks in advance
Read more…
Hi
I am trying to get my camera mount to point in a certain GPS coordinates using the DO_MOUNT_CONFIGURE and DO_MOUNT_CONTROL in the flight planner. May l know how do I set which my camera servo is connected to for the MOUNT mavlink command.
Just like
Read more…I posted a version of 55 that duplicates the Stability patch, but for alt hold. I'd love for a few people to fly it and let me know if it works well for them.
If it's OK, I'll post it to 56.
Jason
http://code.google.com/p/arducopter/downloads/list
Read more…What could cause not being able to change modes while flying but on the ground it works fine?I have solid blue on gps and solid red on imu. If I change modes on te ground it works fine. Take off and I'm stuck in stable mode.I had the problem with .50
Read more…Hello
I had a spare ArduPilot Mega1280 Board and would like to built a small Arducopter something similar to this http://diydrones.com/profiles/blogs/indoor-fun-with-a-tiny.
I will be only using folowing additional features
1. Magnetometer
2. Ultrasonic
Read more…
