Everybody has had his copter spin the engines unwanted and so did i. It bit me two times so i was wondering how to power the ardu without power on the engines or prevent the engines to turn. Ok the wiki states you have to take off the props before f
Read more…I have upgraded my ArduCopter from ArduPiratesNG to ArduCopter 2.0.30 (installed via the MissionPlanner). Everything seems to work, except from the compass.
I used to have the compass connected via a cable, but now I have soldered it onto the shield
Read more…Was this a free download/plugin at one time? I ask because I have seen the youtube video with AI manager running with Map Window GIS. If this is no longer free, is there a way to get an old version to test? Thanks!
Read more…Hello,
Just wanted to thank Happy and Mr. Levine for the work on the GCS, it works and looks GREAT!
Happy, I have all the functions working (airspeed, target altitude, ect.) properly.
Really like the yaw instrument that displays magnetic heading, an
Read more…Hi, I have a MTK 3329 connected to a Ardupilot Mega. The system had been working fine.
Recently, I moved the setup over to another airframe and now I do not appear to be able to read any GPS data at all.
I have tried the GPS test in the Ardupilot
Read more…
Would be interesting to have a "Look at POI" mode, where the camera would stay oriented in the direction of a POI, regardless the model position.
"Care free" mode is interesting as well, it's a mode quite similar as "Look at home", but where the YA
Read more…i just loaded 2.0.29 and when checking status in APM Planner it shows mode as empty until i change to modes then it changes to loiter or auto. i loaded code with arduino and use cli to setup everything.
modes setup ok. i was running 2.0.25 and statu
Read more…Hello everybody,could you please help me with reversing both camera stabilization servos in Arducopter 2 code?Where should I place "minus" sign? Thank you very much. Jakub/// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-#i
Read more…Hello,I finished assembling my ardustation, and everything seems work well.I loaded the Ardustation firmware v 12.I use 2 XBee Pro 60mW Wire Antenna 2.4Ghz (900Mhz is not allowed in Europe) with GPS Mediatek DIYDrones and it works perfectly with Miss
Read more…Hallo everybody,
during flying with hexacopter AC2 firmware 2.025, after exiting alt hold mode, all motors suddenly stops. Free fall from cca 20 m, crash to pieces. Pilot fault excluded (everything as usual). Any ideas?
BtW: Any cheap spare Ardu ele
Read more…I would think it is recommended but is it mandatory?
Tried loiter today with 2.0.28 starts to make circles that get bigger and bigger and then it does a funky 180-360 degree spin that scares me! but nothing stable mode cant handle=)
Iv never really h
Read more…I have no Idea what the latest firmware version is loaded into my Arducopter by Mission Planner. Is it possible to show it somewhere in the APM Mission Planner? Not The Mission Planner version but the Arducopter firmware version.
Neil
Read more…Hello to everyone here. I've been reading the site for some time and finally decided to build my own.
So I've built all my hardware and successfully tested the APM/IMU via the Mission Planner. The sensors worked perfectly.
I've since attached all my R
Read more…I purchased a DroneCell with the intent of integrating it into the AdruPilot and the planner. I just wanted to touch base with the community and see if anyone else has already started down this road before I start writing code.
Read more…I have problems compiling latest build from trunk.This is what I get:C:\Arducopter2.0.2\libraries\AP_IMU/AP_IMU_Oilpan.h: In function 'void slow_loop()':C:\Arducopter2.0.2\libraries\AP_IMU/AP_IMU_Oilpan.h:71: error: 'float AP_IMU_Oilpan::_sensor_comp
Read more…Hi guys,
I've been recommended these by the helpful chaps over at FirstPersonView (fpvuk.org) as just about the only legal setup available in the UK. ie 25 mW at 5.8 GHz. Toal cost without camera £169.
My question is, the receiver provides 3 rca phono
Read more…Does anyone happen to know a good replacement for the HXT 2835 (380S) 2200kv Brushless Inrunner? (Can be found here: http://www.hobbyking.com/hobbyking/store/uh_viewitem.asp?idproduct=5203) It has been out of stock for a while, and I do not know how
Read more…Does anyone know what nut fits on the standard motors for arducopter? I lost the locking nut on top of the propeller and I decided to use normal nuts, but is it M4 or M5?
Read more…I have a std AC frame (no vibration damping, ragged old blades, kind of parallel arms, lots of tape and dings), old board without jumpers. Unit flies great with Ardupirates NG - sonar hold very accurate, good loiter, etc.
I have flown earlier ACM ver
Read more…
