I like the idea of using a HUD in when flying FPV, but how is this done? I found the Remzibi OSD at the diy store. Is this what is used to make videos like this: http://diydrones.com/profiles/blogs/a-newbies-guide-to-uavs
Can this be used with the Xb
Hi!
My name is Vagelis.
I am a newcomer to the u.a.v. world.
I would like to know can i control my u.a.v. with a modem router from my laptop with a joystick?
I am asking because I have seen that the most expensive radio controls are 2,4Ghz and my modem
Hi, guys!
I noticed, on the ArduIMU+ Demo, that the GyroX ( Pitch ) value seemsto be inverted. I assembled it like manual explains (with all the chipsinside the "cube", with their top face pointing to the center of theimaginary box, formed by the boar
My receivers (35MHz) usually go nuts when they loose radio signal.
If I turn OFF the TX the RX can turn the servos off limits and strip their gears, the motor can suddenly start...
Even in Waypoint mode I see that this happens, since you always have
Read more…Hi all,
I m using Futaba 6 channel PCM Transmitter(T6EXAP). It has a two way switch on channel 5, which i want to upgrade to three way switch for my autopilot controls.
Currently in upward position signal width at reciever is 1936(
Hello everybody!
I was looking on sparkfun.com to buy a 3-axis accelerometer for learning and training purposes.
From what I understand, some of the accelerometers have an integrated interface (SPI, I2C, etc...) while others simpler versions output
Read more…Mostly as a understanding/learning exercise I am coding a DCM in Python based on the write up of the ArduIMU. My 'sensor' is a Wii Nunchuck with a Motion+ mounted inside the Nunchuck, interfaced to a PC via I2C.
The bit that I am having brain trouble
Newbie here with some questions. First some background. I have been building and flying R/C aircraft since 1963. Had to build my first transmitter and radio from a bag of parts. Best survelliance aircraft was a 12 foot Sr. Telemaster built in Ger
Read more…Is it ok to get this antenna as the UBlox here is sold out?
Thanks for your help!
http://www.sparkfun.com/commerce/product_info.php?products_id=9436
Its GS407, so I guess i can use the adapter?
I wanna keep this as simple as possible so if I have to inte
What is the best way to connect a laptop to the aircraft? I have a 2.4 Ghz radio for manual control, but what about sending and receiving waypoints and data from the ground? (Sorry to ask a noob question)
Hello,First topic with probably noob questions...I think Im going to buy the "eLogger V3" datalogger: (http://www.eagletreesystems.com/MicroPower/micro.htm) with altimeter micro sensor, airspeed micro sensor, gps module, "FMA Direct™ CPD-4™ X/Y horiz
Read more…hey guys for my project i am supposed 2 build a quadrotor...i am assigned the mechanical aspect of designing the frame ...the specifications that we are looking for the rotorcraft are as follows:total weight of abt 1 kgpayload weight (additional ) 50
Read more…Problem:When I switch to waypoint-mode (ch5 100%) the MUX-LED lights up and the servos starts reacting (OK).BUT, very often (about 40% of the case) the yellow STAT-LED goes off as soon as I enter WP-mode and everything stops working! No servo respons
Read more…hi all.this is shailendra singh.i m preparing my own auto pilot kit with at-mega 128 ,a gps,pitottube,probably gyro,accelerometer combination or gyro and xyz sensorcombination.presently i m working on my pcb layout.but the headache isprogramming part
Read more…Hi, i have a few thoughts about a project i have in mind.Here is my "plan"FeaturesMission Critical- IMU- Between 3-5km operational range (i think this is based on available electrical batteries power)- Automatic waypoint flight without RTB on signal
Read more…HiI came across a US $250 airframe of fiberglass that canmake a good uav platformWingspan: 76” / 1930mmWing Area: 969 sq in/ 62.5 sq dmElevator Area: 16.5 sq dmRudder Area: 13 sq dmFlying Wt: 14.3 lb / 6500gFuselage Length: 71 in/ 1800 mmEngine: 150-
Read more…Years ago a company called RCD made a device called a "Master Onboard Multimixer". A very valuable add on for those interested in CCPM mixing or multi servo operations. I currently use one in my chopper to control the 120 degree swashplate mixing alt
Read more…Hello All,Well, I tried to repair my uBlox antenna, and I'm not sure it went that well.I downloaded u-center, and when I use the same port settings I use to connect to ardupilot, I get this in the "Packet Console". Doesn't seem good, should this app
Read more…Sat 16th the day of truth had come. I made my maidenflight with Easystar. Throttle manual. The Ap would have worked well if my waypoints would have had the expected altitude. Because I was not understanding the rules of "over terrain" my waypoints ha
Read more…I wanted to make a form where people could post their plans for airframe design, and planes that they used that worked well (we know about the easy star, telemaster, and easy glider) I've got one that I think would be really good.It's a giant gliderH
Read more…